KStrong UFA20003 handleiding
Handleiding
Je bekijkt pagina 10 van 13
09
Step 2: Now pass the small attachment O-ring through the large O-ring. Slide the large ring up
to the anchorage structure. Pull the small O-ring down to take up slack that was made
by moving the large ring up. The sling should be tightly wrapped around the anchorage
with the small O-ring hanging free. You may shorten the distance that the small O-ring
hangs from the anchorage by wrapping the sling around the anchorage several times.
On each loop, pass the small O-ring through the large ring.
(Models: )UFA710103, UFA710104 and UFA710106
The Anchor wire rope slings are made of PVC coated galvanized wire rope. The termination of
the wire rope is looped over a steel thimble and secured back on to the wire, and swaged. The
ends of wire rope slings are provided with two O-rings.
INSTALLATION OF KSTRONG WIRE ROPE SLING
Step 1: Place the sling over the anchorage structure in such a way that the two O-rings hang on
each side of the structure. The anchorage structure on to which anchor sling is to be
looped must strong enough to withstand the load of application, and must be free from
sharp and abrasive edges.
Step 3: Use the small O-ring as the attachment point for personal fall arrest system, once the
installation is complete.
Step-1 Step-2
Step-3
direction
of loading
INSTALLATION OF CROSS ARM STRAPS
Step 2: Loop the entire strap around the underlying structure, so that there
remains no excess webbing.
Step 3: This cross arm strap is provided with loops at both ends. Pass one loop
through the other loop and pull it until strap is completely taught and
cinched tightly. Multiple passes of the tie-off adaptor around the
anchorage may be made to shorten the length. Pass one web loop
through the other web loop on each pass.
Step 1: Loop the cross arm strap around a suitable and strong structure.
(Models: UFA21004 and UFA21006 )
Note: The label on the strap should face outwards, and the structure on to which
cross arm strap is to be looped must be free from sharp and abrasive edges. If
however, there is presence of sharp, abrasive surface on the structure, then this
should be covered with a suitable covering recommended for such use.
Step 4: Use the protruding loop of the strap to anchor the connecting element of
the personal fall arrest system.
INSTALLATION OF CROSS ARM STRAPS
Step 1: Loop the cross arm strap around a suitable and strong structure.
Note: The label on the strap should face outwards, and the structure on to which
cross arm strap is to be looped must be free from sharp and abrasive edges. If
however, there is presence of sharp, abrasive surface on the structure, then this
should be covered with a suitable covering recommended for such use.
Step 3: Loop the entire strap around the underlying structure, so that there remains
no excess webbing. Each time while looping, pass the small D-ring through
the large D-ring. Continue till all the excess webbing is used up.
Step 4: Use only the small D-ring to anchor the connecting element of the
personal fall arrest system.
(Models: UFA20003, UFA20004, UFA20006, UFA20010, UFA20016,
UFA20024 and UFA20030)
Step 2: Pass the small D-ring through the large D-ring of the cross arm strap,
and cinch tightly.
Step-1 Step-2
Step-3
direction
of loading
Bekijk gratis de handleiding van KStrong UFA20003, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | KStrong |
| Model | UFA20003 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1499 MB |
