Krups Espresseria EA8250 handleiding
Handleiding
Je bekijkt pagina 15 van 94
2524
ENGLISH
PROBLEMS CORRECTIVE ACTIONS
The steam does not come
out of the nozzle.
After switching off your appliance and leaving it to cool:
Make sure the tip of the steam nozzle is properly
afxed. Make sure the steam nozzle is not clogged at
the aerator (if necessary clean the steam nozzle aerator
with the needle supplied). Empty the tank and remove
the Claris lter. Fill the tank with mineral water high in
calcium (> 100 mg/litre or .015oz/gallon), it may take as
many as 5 to 10 cycles of steam at 60 seconds each
cycle to achieve a continuous jet of steam.
There is not enough milk
froth.
Using the needle supplied unblock the small air inlet at
the top of the nozzle if required.
Use a cold container and milk that has been opened
recently.
Try changing the type of milk if this does not work (UHT
or pasteurised).
The milk froth is too bubbly.
Check that the two ends of the small stainless steel
tube are tted correctly into the exible part of the
steam nozzle.
The Auto-Cappuccino
accessory does not suck
the milk (accessory sold
separately).
Ensure that the tube immersed in the milk is not
blocked.
Check that the exible tube is not twisted and that it is
correctly tted into the accessory to avoid any air being
sucked in.
After switching off your appliance and leaving it to cool,
unblock the outlet of the Auto-Cappuccino accessory.
After emptying the coffee
grounds collector, the
warning message is still
displayed on the screen.
Correctly replace the coffee grounds collector and
follow the instuctions on the screen. Wait at least 6
seconds before replacing them.
The power has been cut off
during a cycle.
The appliance resets itself automatically when the
power is switched back on and is ready for a new cycle.
There is water or coffee
underneath the appliance.
The drip collector tray has overowed: empty it and
clean the coffee grounds collector. Check that the drip
tray is tted correctly.
Do not remove the water tank before the end of the
cycle.
A message
appears.
Unplug the appliance for 20 seconds, remove the Claris
cartridge and if required, put it back into service.
If the fault persists, note the fault number and contact
KRUPS’ Customer Service.
If coffee ows behind the
coffee nozzles.
Pour cold or room-temperature water into the tank.
Reduce the temperature level.
You can stop your appliance at all times: the appliance will emit two beeps and then it will
stop soon afterwards.
PROBLEMS AND CORRECTIVE ACTIONS
PROBLEMS CORRECTIVE ACTIONS
The appliance does not
switch on when the “On/Off”
is pressed.
Check that the plug of the power cord is pushed
correctly into the mains socket.
Water or steam comes
incorrectly out of the steam
nozzle.
In case of repeated operation, several drops may drip
from the steam nozzle.
The espresso or coffee is not
hot enough.
Change the coffee temperature setting.
Heat the cups by rinsing them with hot water.
The coffee is too light or not
strong enough.
Check that the coffee bean tank has coffee in it and that
it is owing correctly. Avoid using oily, caramelised or
avoured coffee.
Reduce the volume of coffee using the central knob.
Turn the grinding neness knob towards the left for
a ner grind. Prepare in two cycles using the 2 cup
function.
The coffee ows too slowly.
Turn the grinding neness knob towards the right for a
coarser grind (may depend on the type of coffee used).
Carry out one or two rinsing cycles.
The coffee is not creamy
enough.
Turn the grinding neness knob towards the left for a
ner grind (may depend on the type of coffee used).
Change the Claris Aqua Filter System cartridge (follow
the installation procedure on page 13).
Carry out one or two rinsing cycles.
The appliance does not serve
any coffee.
An incident has been detected during the preparation.
The appliance resets itself automatically and is then
ready for a new cycle.
Why can I not run descaling/
why does my machine not
request a descaling cycle?
The machine only requests a descaling cycle once it has
made a certain number of drinks using steam.
You have used ground coffee
instead of bean coffee.
Use your vacuum cleaner to suck out the pre-ground
coffee in the coffee bean tank.
The grinder makes a strange
noise.
There are foreign particles in the grinder. Contact
KRUPS’ Customer Service.
The grinding neness knob is
hard to turn.
Only change the grinder setting when it is operating.
Bekijk gratis de handleiding van Krups Espresseria EA8250, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Krups |
| Model | Espresseria EA8250 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 15677 MB |
