Janome Horizon Memory Craft 9480QCP handleiding

Naaimachine

Janome

164 pagina's

PDF beschikbaar

Handleiding

Utility Applique Quilt Bridge Decorative

Press the auto-lock button to sew a locking stitch

immediately. The machine will automatically stop.

When the machine is stopped, press the auto-lock

button and the LED signal (7) will blink. The machine

will immediately sew locking stitches and automatically

stop when the machine is started.

•

When any other stitches are selected:

Press the auto-lock button to sew a locking stitch

at the end of current pattern. The machine will

automatically stop.

When the machine is stopped, press the auto-lock

button and the LED signal (7) will blink. The machine

will sew a locking stitch at the end of the current pattern

and automatically stop when the machine is started.

The machine will trim the threads automatically after

locking the stitch when the auto thread cutting is

turned on (refer to page 143).

(4) Needle up/down button

Press this button to bring the needle bar up or down.

The machine will stop with the needle in down position.

However, you can change the needle stop position in the

machine setting mode (refer to page 143).

(5) Presser foot lifter button

The presser foot will go up or down by pressing this

button.

You can also use the presser foot lifter and knee lifter to

raise and lower the presser foot (refer to pages 19 and

35).

(6) Thread cutter button

After nishing sewing, press this button to trim the

threads. The needle bar automatically rises after trimming

the threads (refer to page 43).

The LED signal (8) blinks when the machine trims

threads.

Machine Operating Buttons

(1) Start/stop button

Press this button to start or stop the machine.

The machine starts running slowly for the rst few

stitches, then runs at the speed set by the speed control

slider. The machine runs slowly as long as this button is

pressed.

The button will turn red when the machine is running, and

blue when it has been stopped.

Pressing and holding this button while sewing will slow

down the sewing speed and the machine will stop when

the button is released.

(2) Reverse button

•

When the following stitch patterns are selected:

NOTE:

There will be particular functions of the reverse

button when stitch pattern U2, U3, B2, B13, or B14 is

selected. Refer to pages 48, 63-64, 69 and 122 for

instructions.

(3) Auto-lock button

•

When the following stitch patterns are selected:

Utility Applique Quilt Bridge Decorative

The machine will sew in reverse as long as the reverse

button is pressed. Release the button to sew forward.

When the machine is stopped and foot control is

disconnected, the machine will sew in reverse slowly

as long as the reverse button is pressed. Release the

button to stop the machine.

•

When any other stitches are selected:

If you press the reverse button when sewing any other

patterns, the machine will immediately sew locking

stitches and automatically stop.

(1)

(2)

(3) (4) (5) (6)

(7) (8)

NOTE:

• The start/stop button cannot be used when the foot

control is connected to the machine.

• You can select the desired start-up speed from slow,

medium or high (refer to page 144).

NOTE:

• The thread cutter button does not function:

- directly after turning on the power.

- when the presser foot is raised with the foot lifter.

- after being pressed 3 times in a row.

• Use the thread cutter on the face plate if the thread

is #30 or thicker (refer to page 43).

After using auto thread cutting or threading the bobbin

holder, you can start sewing without drawing up the

bobbin thread.

Bekijk gratis de handleiding van Janome Horizon Memory Craft 9480QCP, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.