IKEA SÖDERBODA 306.027.21 handleiding
Handleiding
Je bekijkt pagina 10 van 28
ENGLISH
10
Settings
The water softener
The water softener removes minerals from the water
supply, which would have a detrimental eect on the
washing results and on the appliance.
The higher the content of these minerals, the
harder your water is. Water hardness is measured in
equivalent scales.
The water softener should be adjusted according to
the hardness of the water in your area. Your local
water authority can advise you on the hardness of the
water in your area. It is important to set the right level
of the water softener to assure good washing results.
Water hardness
German
degrees (°dH)
French
degrees
(°fH)
mmol/l
Clarke
degrees
Water
softener
level
Salt
consumption
(gram/cycle)
Regeneration
frequency (Every
X cycles)
35 - 55 61 - 98 6.1 - 9.8 43 - 69 H6 60 1
23 - 34 41 - 60 4.1 - 6.0 29 - 42 H5 30 2
18 - 22 31 - 40 3.1 - 4.0 22 - 28 H4 20 3
12 - 17 21 - 30 2.1 - 3.0 15 - 21 H3
1)
12 5
6 - 11 10 - 20 1.0 - 2.0 7 - 14 H2 9 10
0 - 5 0 - 9 0 - 0.94 0 - 6 H1
2)
0 NO
1) Factory setting.
2) Do not use salt at this level.
Whether you use a standard detergent or
multi-tabs (with or without salt), set the proper
water hardness level to keep the salt rell
notication active.
Multi-tablets containing salt are not eective
enough to soften hard water.
During every regeneration, an additional 2.0 liters
of water is required, energy consumption increases
by 0.02kWh and the programme is extended by
4minutes.
How to set the water softener level
1. Close the dishwasher door and press the On/O
button to switch the appliance on.
2. Within 60 seconds after switching on, press the
button for more than 5 seconds to enter the water
softener setting mode.
3. Press the button to select the correct setting
according to your local water hardness, the setting
will change in the following order:
H3->H4->H5->H6->H1->H2.
4. Wait 5 seconds or press the On/O button to
conrm the setting and exit.
The rinse aid empty notication
The rinse aid helps to dry the dishes without streaks
and stains. For best drying performance, always use
rinse aid.
The rinse aid is automatically released during the hot
rinse phase.
When rinse aid dispenser is empty, the rinse aid
indicator ( ) lights up reminding you to rell rinse
aid.
The rinse aid level
It is possible to set the released quantity of rinse aid
between “d1” level (minimum quantity) and “d5” level
(maximum quantity).
The factory setting is d3.
How to set the rinse aid level
1. Close the door and switch on the appliance.
2. Within 60 seconds after switching on, press the
button for more than 5 seconds, and then press
the Delay+ button to enter rinse aid level setting,
the rinse aid indicator will ash.
3. Press the button to select the proper setting
according to your usage habits, the setting will
change in the following order: d3->d4->d5->d1->
d2->d3.
The higher the number, the more rinse aid the
dishwasher uses.
Bekijk gratis de handleiding van IKEA SÖDERBODA 306.027.21, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | IKEA |
| Model | SÖDERBODA 306.027.21 |
| Categorie | Vaatwasser |
| Taal | Nederlands |
| Grootte | 3083 MB |
