Icom IC-F6062D handleiding
Handleiding
Je bekijkt pagina 2 van 2
PANEL DESCRIPTION FUNCTION DISPLAY
REAR PANEL CONNECTION
1
ANTENNA CONNECTOR
Connect to an antenna. Contact your dealer about
antenna selection and placement.
2 EXTERNAL SPEAKER JACK
Connect a 4 ~ 8 Ω external speaker.
3 D-Sub 25-pin
Connects to an external unit.
4
MICROPHONE HANGER
Connect the supplied microphone hanger to the
vehicle’s ground for microphone ON/OFF hook
functions. (See ‘PANEL DESCRIPTION’ for details.)
5 IGNITION LEAD
Connects to an ignition line.
CAUTION: DO NOT
put a pressure on
this lead. Binding to the DC power cable is
recommended.
6
DC POWER RECEPTACLE.
Connects to a 12 V DC battery. Pay attention to
polarities.
R WARNING! NEVER connect to a 24 V battery. This
will damage the transceiver.
D About the LED indicator
• Lights red while transmitting.
• Lights green while receiving a signal, or when the
squelch is open.
D About the Microphone connector
Connect the supplied or optional microphone.
NEVER connect non-specied microphones. The pin
assignments may be dierent and may damage the
transceiver.
[VOL]
LED indicator Up/Down keys
Power key [ ]
Dealer-assignable keys*
[P0], [P1], [P2], [P3], [P4]
*Ask your dealer for details.
Function display Speaker
Microphone
connector
D MICROPHONE
The supplied or optional microphone has a PTT switch
and a hanger.
• The following functions are available when you put the
microphone ON hook, or take it OFF hook (depending on
the presetting):
- Automatic scan starts when you put it ON hook.
- Scan is paused or cancelled when you take it OFF
hook.
- Automatically selects the Priority A channel when you
take it OFF hook.
- Sets to the ‘Inaudible’ (mute) mode when you put it ON
hook.
-
Sets to the ‘Audible’ (unmute) mode when you take it
OFF hook
.
q SIGNAL STRENGTH ICON
Displays relative receive signal strength level.
Weak Receive Signal level Strong
w LOW POWER ICON
Displayed when low output power is selected.
e AUDIBLE ICON
➥ Displayed when the channel is in the ‘Audible’
(unmute) mode.
➥ Displayed when a matching signal is received.
r COMPANDER ICON
➥ Displayed when the Compander function is
activated.
When the GPS indicator setting is ON*
➥ Displayed when the GPS receiver acquires the GPS
signal from a satellite. In this case, the compander
icon does not show the Compander function’s
status.
*Ask your dealer for details.
t SCRAMBLER ICON
Displayed when the Voice Scrambler function is
activated.
y BELL ICON
Displayed or blinks when a matching signal is
received, according to the presetting.
u CALL CODE MEMORY ICON
Displayed when the call code memory is selected.
i SCROLL ICON
Displayed when an SDM (Short Data Message),
including more than 12 characters, is selected in the
received message log screen by using [BIIS Button] or
[dPMR Button].
†, ‡
o MESSAGE ICON
Displayed when an SDM or Status message is received.
†, ‡
!0 ALPHANUMERIC DISPLAY
➥ Displays an operating channel number, channel
name, User Set mode contents, DTMF code, etc.
➥ Depending on the presetting, characters are displayed
in 1 line or 2 lines on the LCD.
• In the instruction manual, the LCD illustration is
described as having characters displayed in 2 lines.
!1 ACTIVATED KEY ICON
Displayed above the key assigned as [Scan], [Scan Add/
Del(Tag)], [Lock], [Talk Around], [Surveillance] and [BIIS
Button]
†
, while that key is activated.
†
BIIS operation only
‡
dPMR operation only
Icom Inc.
!1
qw erty iuo
!0
D Turning power ON
z Hold down [ ] to turn ON the power.
NOTE: If the transceiver is programmed for a start up
password, input the digit codes as directed by your
dealer. See the operating guide for details.
D Receiving and Transmitting
Receiving:
1. Select a channel.
z Push [CH Up] or [CH Down].
z Push one of the direct channel select keys,
[MR-CH 1] to [MR-CH 4].
2. When receiving a call, rotate [VOL] to adjust the audio
output level to a comfortable listening level.
Transmitting:
Wait until the channel is clear to avoid interference.
1. Take the microphone off the hook.
• While scanning, the scan stops.
2. Wait for the channel to become clear.
• The channel is busy when the LED indicator lights green.
3. While holding down [PTT], speak at a normal voice
level.
4. Release [PTT] to receive.
IMPORTANT:
To maximize the readability of your signal:
1. After pushing [PTT], pause briefly before you start
speaking.
2. Hold the microphone 5 to 10 cm (2 to 4 inches)
from your mouth, then speak at a normal voice
level.
BASIC OPERATION
D For mobile operation D For base station operation
Antenna
Antenna
To an
AC outlet
DC Power
supply 13.2 V
Red
Red
Black
Black
Optional Speaker
Optional Speaker
Microphone
Microphone
q
q
w
w
e
e
r
r
t
t
y
y
12 V
Battery
NOTE: Use the terminals as shown
below for the cable connections.
Crimp Solder
R WARNING! NEVER
remove the fuse holders
from the DC power cable.
R WARNING! NEVER
remove the fuse holders
from the DC power cable.
1
ANTENNA CONNECTOR
2 EXTERNAL SPEAKER JACK
3 D-Sub 25-pin
4
MICROPHONE HANGER
5 IGNITION LEAD
6
DC POWER RECEPTACLE.
Connects to a 13.2 V DC power supply. Pay attention
to polarities. Make sure the ground terminal of the DC
power supply is grounded.
NOTE: The antenna
connector typr may
dier, depending on the
transceiver versions.
NOTE: The antenna
connector typr may
dier, depending on the
transceiver versions.
Bekijk gratis de handleiding van Icom IC-F6062D, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Icom |
| Model | IC-F6062D |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 715 MB |
