Hughes & Kettner Tube 100 handleiding
Handleiding
Je bekijkt pagina 8 van 26
0
5
10 0
5
10 0
5
10
-5
0
+5 -5
0
+5
-5
0
+5
0
5
10
-5
0
+
-5
0
+5
0
5
10
-5
0
+5 -5
0
+5
-5
0
+5
0
5
10
-5
8
TUBE 50/100 - MANUAL
MIDI LEARN: Installation of the MSM-1 MIDI Module is a prerequisite
for MIDI capability. After installation, the STAGEBOARD switching func-
tions can be executed via MIDI Program Change messages. Pressing the
MIDI LEARN button will save the current switch settings.
PRESENCE: This pot determines the overtone content in the
signal and the aggressiveness of the tone. Note that when you
turn the POWER pot down, the overtone spectrum is more pro-
nounced. Consequently, these pots work interactively - so you
have more control over the sound spectrum at all volume
levels.
REVERB BUTTON: Press this button to activate the
REVERB section. The REVERB circuit remains active for as
long as this button on the front panel is in the "ON" posi-
tion. If you wish to use the Stageboard to switch Reverb
on and off (with switch „3“), you must leave the front
panel Reverb button set to "OFF".
REVERB: This pot controls the amount of integrated
reverb added to the signal when the REVERB BUTTON
is in the "ON" position.
FX LOOP BUTTON: With this front panel button pressed in,
the FX LOOP will always be active. If not depressed, its fun-
ction is taken over by switch „3“ on the stageboard.
FX- MIX: Varies from all ‚dry‘ (preamp signal only) to all ‚wet‘
(the FX signal fed from an external effects device to the FX
RETURN JACK), and any combination in between - assuming the
FX Loop has been activated.
STANDBY: The standby switch is self-explanatory, it
mutes the amp during breaks. The power amp tubes
are protected in standby mode. When you turn the
amp back to full power, the tubes are already warm.
MAINS: Power
ON/OFF switch.
POWER AMP: Determines the output power, and thereby the volu-
me, of the TUBE 50 / TUBE 100. In contrast to conventional master
controls, the enhanced overtones and compressive effect of the
TUBE 50 / TUBE 100 power amp section are audible even at low
POWER AMP settings. At the maximum setting, the TUBE 50 /
TUBE 100 operates like any amp without a master control - i.e. the
amount of power amp distortion is determined by the preamp's out-
put signal level.
CHANNEL SELECT: This channel selector switches between CHANNEL 1 and
CHANNEL 2. In combination with the different AMP MODES, you have four diffe-
rent basic sounds available at the touch of a button. This switching function can
also be performed via the Stageboard (Button 2) - provided the button located on
the front panel is in the "OFF" position (CHANNEL).
CHANNEL/AMP MODE SELECT
LEDs: Two illuminated LEDs
indicate AMP MODE B is
active, a single iluminated LED
indicates AMP MODE A is
active. The yellow LEDs indica-
te CHANNEL 1 is active, the red
LEDs indicate CHANNEL 2 is
active.
CHANNEL 2 GAIN: Effectively determines the
degree of distortion for both AMP MODES in
CHANNEL 2.
CHANNEL 2 MASTER: Determines the volu-
me for both AMP MODES in CHANNEL 2.
EQ SECTION: Common BASS, MID and TREBLE tone controls for CHAN-
NEL 2. Here too, MID and TREBLE influence each other for the widest pos-
sible range of subtle tonal variations.
Bekijk gratis de handleiding van Hughes & Kettner Tube 100, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hughes & Kettner |
| Model | Tube 100 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4419 MB |
