Hughes & Kettner Coreblade handleiding
Handleiding
Je bekijkt pagina 14 van 66
14
C o r e b l a d e
in bank 16 to preset B in bank 17 (UP) or bank 15 (DOWN). Here’s how to
activate DIRECT MODE:
• Press and hold TAP, and then press PRESET A.
• First release PRESET A, and then TAP. e decimal point in the display lights
up.
Follow the same sequence to deactivate DIRECT MODE. Note that it is a
volatile rather than a permanent mode. C o r e b l a d e automatically
reverts to standard mode when you switch the amp off.
7.2.2 Setting the FSM 432’s MIDI Send Channel
If you wish to switch devices connected to C o r e b l a d e MIDI THRU -
say, a MIDI multi-effector – using the FSM 432, ensure it is set to the FSM 432’s
MIDI channel or to OMNI. Consult the device’s manual for more info.
To set the FSM 432’s MIDI send channel, proceed as follows:
• Turn C o r e b l a d e on while pressing the FSM 432’s PRESET A button.
e display flashes.
• Release button A. Use UP/DOWN to view and set the MIDI channel to a
number between 1 and 16.
• Quit and store by pressing the PRESET A button.
CAUTION: If COREBLADE and the FSM 432 are not set to the same MIDI
channel, the amp will not respond to program changes! Activating OMNI solves
the problem if all else fails. See section 7.3 for more on this. The factory default
is channel 1.
HEADS UP: If an external effect device is connected to MIDI THRU and you
want to switch COREBLADE and the effect device simultaneously with the
same program change command, you must configure COREBLADE’s STORE
function and program this device accordingly.
NOTE: The table below should be big help if you wish to switch the presets of
a device connected to the MIDI THRU directly via the FSM 432. It shows the
program changes sent by the bank/ preset combination. Please bear in mind that
some MIDI devices switch program 1 via program change command 0. If this is
the case with your outboard gear, simply add a 1 to each value indicated in this
table to activate the desired program.
Bank
Preset
Programchange
Number
Bank
Preset
Programchange
Number
Bank
Preset
Programchange
Number
Bank
Preset
Programchange
Number
1 A 0 9 A 32 17 A 64 25 A 96
1 B 1 9 B 33 17 B 65 25 B 97
1 C 2 9 C 34 17 C 66 25 C 98
1 D 3 9 D 35 17 D 67 25 D 99
2 A 4 10 A 36 18 A 68 26 A 100
2 B 5 10 B 37 18 B 69 26 B 101
2 C 6 10 C 38 18 C 70 26 C 102
2 D 7 10 D 39 18 D 71 26 D 103
3 A 8 11 A 40 19 A 72 27 A 104
3 B 9 11 B 41 19 B 73 27 B 105
3 C 10 11 C 42 19 C 74 27 C 106
3 D 11 11 D 43 19 D 75 27 D 107
4 A 12 12 A 44 20 A 76 28 A 108
4 B 13 12 B 45 20 B 77 28 B 109
4 C 14 12 C 46 20 C 78 28 C 110
4 D 15 12 D 47 20 D 79 28 D 111
5 A 16 13 A 48 21 A 80 29 A 112
5 B 17 13 B 49 21 B 81 29 B 113
5 C 18 13 C 50 21 C 82 29 C 114
5 D 19 13 D 51 21 D 83 29 D 115
6 A 20 14 A 52 22 A 84 30 A 116
6 B 21 14 B 53 22 B 85 30 B 117
6 C 22 14 C 54 22 C 86 30 C 118
6 D 23 14 D 55 22 D 87 30 D 119
7 A 24 15 A 56 23 A 88 31 A 120
7 B 25 15 B 57 23 B 89 31 B 121
7 C 26 15 C 58 23 C 90 31 C 122
7 D 27 15 D 59 23 D 91 31 D 123
8 A 28 16 A 60 24 A 92 32 A 124
8 B 29 16 B 61 24 B 93 32 B 125
8 C 30 16 C 62 24 C 94 32 C 126
8 D 31 16 D 63 24 D 95 32 D 127
7.2 Setting MIDI Channel and Switching OMNI On/O
Press the SERIAL button longer than two seconds when C o r e b l a d e
is in standard operating mode, and the light on the NOISE GATE LED will
start flashing. is assigns special programming functions to the amp’s LEDs and
buttons:
• FX-ON: Now serves as a +1/UP button for setting the MIDI channel
• SERIAL: Now serves as a -1/DOWN button for setting the MIDI channel
• Switches OMNI mode on and off. If the STORE button (OMNI ON)
lights up, C o r e b l a d e responds to all incoming program changes,
irrespective of the MIDI channel over which they are sent. If the light on the
button is extinguished (OMNI OFF), it responds only to messages sent via the
defined MIDI channel.
HEADS UP: OMNI ON is helpful if you are unsure which channel a connected
MIDI device is using to send messages.
During the MIDI setup routine, the LEDs that normally indicate the preamp
channel indicate the MIDI channel. e following table shows MIDI channel
settings:
MIDI-
Channel
Clean Drive Ultra Ultra
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Press and hold SERIAL for a few moments to quit the MIDI setup routine and
store the settings. e amp returns to its most recent operating status (standard
mode).
Bekijk gratis de handleiding van Hughes & Kettner Coreblade, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hughes & Kettner |
| Model | Coreblade |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 19467 MB |
