Hughes & Kettner Attax 200 handleiding
Handleiding
Je bekijkt pagina 7 van 48
7
ATTAX-MANUAL
ENGLISH
FX MIX MASTER
DRY
WET
REVERB
0
5
10 0
5
10
FX LOOP
-5
0
+5
MAINS
DEPTH
0
5
10
RATE
0
5
10
LEAD MASTER
0
5
10
TREBLE
-5
0
+5
MID
-5
0
+5
BASSLEAD GAIN
0
5
10
DEPTH
0
5
10
E
10
CHORUSMODE 2CHORUS
LEAD MASTER
MAINS: AC power switch.
MADE IN ST. WENDEL GERMANY
Max. power
consumption
480 VA
OUTPUT 120 WATTS
MIN. IMP. 4 Ohms
CAUTION!
TO PREVENT THE RISK OF FIRE AND
SHOCK HAZARD DON´T EXPOSE
THIS APPLIANCE TO MOISTURE OR
RAIN. DO NOT OPEN CASE;
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
LEAVE ENOUGH SPACE FOR PROPER VENTILATION!
STEREO FX-LOOP
RETURN
RIGHT
50 - 60 Hz
230 V~
117 V~
100 V~
HEAD
PHONES
OUTPUT 120 WATTS
MIN. IMP. 4 Ohms
LR
SEND
LR
-10 dB
SPEAKERS
LEFT RIGHT
ATTAX 200
RECORDING OUT
LEFT
MONO MONO
TO INSTALL MIDI MODULE:
DISCONNECT AC POWER CORD
BEFORE REMOVING THIS COVER
Ser. No.
MAINS: Connect the included Euro-
norm mains cord to this socket.
Ensure the amp's voltage rating
matches your local AC voltage
rating before you plug the cord into
the wall socket.
HEADPHONES: 1/4" headphone
jack. In order to switch the main
speaker off, unplug the speaker
cable.
SPEAKERS RIGHT: Right
channel speaker output
jacks.
RECORDING OUT L/R: These
output jacks can feed a mixing
console or additional (stereo)
power amp.
SEND: If you are using a stereo signal proces-
sor, connect these jacks to the processor's
INPUT jacks. For mono operation, connect
only the ATTAX 200's SEND R jack to the
processor's INPUT jack.
RETURN L/R: If you are using a stereo signal processor, connect these jacks to
the processor's OUTPUT jacks. For mono operation, connect the RETURN L
jack only.
- 10 db SWITCH: This switch allows you to redu-
ce the signal level being sent to external effects
devices. Press this switch for instrument level
processors (e.g. stomp boxes).
SPEAKERS LEFT: Two 1/4" output jacks for connecting speakers to
the left channel. The two jacks are wired in parallel. Ensure the
overall impedance does not drop below 4 ohms for these two out-
puts. For the ATTAX 200 combo, you can connect an additional
speaker cabinet (at least 8 ohms/60W) in parallel to the internal
speaker.
For the head version, you can connect one cabinet (at least 4
ohms/120W) or two 8-ohm cabinets.
GREEN CHORUS LED: Denotes the chorus effect is active in the CLEAN and
CRUNCH channels by flashing at the selected modulation frequency
RED LEAD LED: The red LED illuminates
when the LEAD channel is active.
MODE 2: Selects either the LEAD 1 or LEAD
2 modes. LEAD 2 is active when the button is
pressed. Once the MSM-1 Module has been
installed, this switching function can be exe-
cuted via MIDI.
LEAD SELECTOR SWITCH: Switches back and forth between the
CLEAN/CRUNCH section and the LEAD channel. The LEAD channel is
active when the button is depressed. Once the MSM-1 Module has been
installed, this switching function can be executed via MIDI
RED MODE 2 LED: This red LED illumi-
nates when the LEAD 2 mode is active.
GREEN CHORUS LED: Denotes
the chorus effect is active in the
LEAD channel by flashing at the
selected modulation frequency
CHORUS SELECTOR SWITCH:
Activates the chorus effect for all
channels.
DEPTH: Controls the chorus effect's
modulation depth for the CLEAN and
CRUNCH channels
FX LOOP SELECTOR: Activates the
ATTAX 200 FX LOOP. Once the MSM-
1 Module has been installed, this swit-
ching function can be executed via
MIDI.
FX MIX: This control lets you decide how
much of the processed signal is mixed in
with the original signal. Determines the
original signal's volume and its relations-
hip to that of the connected effects devi-
ce's processed signal. DRY = original sig-
nal only, WET = processed signal only
MASTER: Determines the over-
all output level of the ATTAX
200. The level of the RECOR-
DING OUT signal is unaffec-
ted by the MASTER control.
GREEN FX LED: Lights when
the ATTAX 200 FX LOOP is
active.
LEAD GAIN: Determines the
amount of distortion in the
LEAD channel
DEPTH: Controls the chorus effect's
modulation depth for the CLEAN
and CRUNCH channels.
EQ SECTION: Active BASS, passive MID
and TREBLE tone controls for the LEAD
channel. Here too, MID and TREBLE influ-
ence each other for the widest possible
range of subtle tonal variations.
RATE: Controls the chorus effect's modulati-
on rate for the LEAD channel. At a RATE set-
ting of approximately 12 o'clock, the
"Vintage Rotary Effect" kicks in.
LEAD MASTER:
Controls the volume
of the LEAD chan-
nel.
REVERB: Controls how much integrated
reverb is added to the signal. Reverb is
automatically adjusted for each channel
when you switch channels.
Bekijk gratis de handleiding van Hughes & Kettner Attax 200, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hughes & Kettner |
| Model | Attax 200 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7661 MB |
