Handleiding
Je bekijkt pagina 9 van 20
9
CLEANING AND MAINTENANCE
Make sure that the oven has
cooled down before carrying out
any maintenance or cleaning.
Do not use steam cleaners.
Do not use wire wool, abrasive
scourers or abrasive/corrosive
cleaning agents, as these could
damage the surfaces of the
appliance.
Wear protective gloves.
The oven must be disconnected
from the mains before carrying
out any kind of maintenance
work.
Make sure that the oven has
cooled down before carrying out
any maintenance or cleaning.
Do not use steam cleaners.
Do not use wire wool, abrasive
scourers or abrasive/corrosive
cleaning agents, as these could
damage the surfaces of the
appliance.
Wear protective gloves.
The oven must be disconnected
from the mains before carrying
out any kind of maintenance
work.
EXTERIOR SURFACES
Clean the surfaces with a damp microfibre cloth. If
they are very dirty, add a few drops of pH-neutral
detergent. Finish off with a dry cloth.
Do not use corrosive or abrasive detergents. If any of
these products inadvertently comes into contact with
the surfaces of the appliance, clean immediately with
a damp microfibre cloth.
INTERIOR SURFACES
• After every use, leave the oven to cool and then
clean it, preferably while it is still warm, to remove
any deposits or stains caused by food residues. To
dry any condensation that has formed as a result
of cooking foods with a high water content, leave
the oven to cool completely and then wipe it with
a cloth or sponge.
• If there is stubborn dirt on the interior surfaces,
we recommend running the automatic cleaning
function for optimal cleaning results. Avoid
activating the pyrolitic cycle cleaning in the
presence of limescale residues. Before activating,
perform limescale cleaning as described above.
• The door can be easily removed and refitted to
facilitate cleaning of the glass.
• Clean the glass in the door with a suitable liquid
detergent.
ACCESSORIES
Soak the accessories in a washing-up liquid solution
after use, handling them with oven gloves if they
are still hot. Food residues can be removed using a
washing-up brush or a sponge.
REMOVING AND REFITTING THE DOOR
b
a
1. To remove the door, open
it fully and lower the
catches until they are in the
unlock position.
a
b
~15°
2. Close the door as much
as you can. Take a firm hold
of the door with both hands
– do not hold it by the
handle. Simply remove the
door by continuing to close
it while pulling it upwards
at the same time until it is
released from its seating. Put the door to one side,
resting it on a soft surface.
3. Refit the door by moving it towards the oven,
aligning the hooks of the hinges with their seating
and securing the upper part onto its seating.
b
a
4. Lower the door and then
open it fully. Lower the
catches into their original
position: Make sure that
you lower them down
completely.
Apply gentle pressure to check that the catches are in
the correct position.
5. Try closing the door and check to make sure that it
lines up with the control panel. If it does not, repeat
the steps above: The door could become damaged if
it does not work properly.
LOWER THE UPPER HEATING ELEMENT
1. Extract the heating element from its seating, then
lower it.
2. To return the heating element to its position, lift it
up, pull it slightly towards you and make sure that the
tab support is in its proper seating.
Bekijk gratis de handleiding van Hotpoint HAO3 K58HSU W, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hotpoint |
| Model | HAO3 K58HSU W |
| Categorie | Oven |
| Taal | Nederlands |
| Grootte | 3304 MB |
