Hotpoint HA6IB16B2M6L0 handleiding
Handleiding
Je bekijkt pagina 4 van 16
EN
4
Quick Guide
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or is-
sues please contact authorized After-sales Service whose contact details can be found in the warranty booklet. Spare parts will be available
for aperiod of either up to 7 or up to 10 years, according to the specic Regulation requirements.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
Descale
indicator is lit
or blinking;"dES"
alarm is displayed.
Limescale is accumulating on internal com-
ponents of the appliance.
Descale the appliance immediately using the Self Clean program and acommercially
available descaling product (see OPTIONS AND FUNCTIONS). Rell the reservoir with
salt. Check the water hardness setting. If the appliance is not descaled, it will stop
functioning.
The dishwasher
won’t drain.
Display shows:
F7 E3 or F9 E1
The lter is clogged with food residues or
limescale
Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and
DESCALE INSTRUCTION).
The drain hose is kinked. Check the drain hose (see INSTALLATION INSTRUCTION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The dishwasher
does not ll the
water.
The display
shows: H
2
O and
is lit; acoustic
alarm sounds.
No water in the water supply or the tap is
closed.
Make sure there is water in the water supply and the water tap is open.
The water inlet hose is kinked.
Check the inlet hose (see INSTALLATION). Open dishwasher door, press START/Pause
button and close the door within 4 seconds.
The screen in the water inlet hose is
clogged; it is necessary to clean it.
Check and clean the screen in the water inlet hose. Open dishwasher door, press
START/Pause button and close the door within 4 seconds.
The dishwasher
nishes the cycle
prematurely.
The display
shows: F8 E3
The lter is clogged with food residues or
limescale.
Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and
DESCALE INSTRUCTION).
Drain hose positioned too low or siphoning
into the home sewage system.
Check if the end of the drain hose is placed at the correct height (see INSTALLATION).
Check for siphoning into the home sewage system, and install a siphon breaker/air admit-
tance valve if necessary.
An excessive amount of foam is present.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER).
Air in the water supply. Check water supply for leaks or other issues letting air inside.
The dishes are not
dried well.
Rinse aid is not present or the dosage is too
low.
Make sure the rinse aid dispenser is lled (see FILLING THE RINSE AID DISPENSER).
Multifunctional tablets only will not provide as good drying eects as the actual use
of liquid rinse aid.
The dishes have been unloaded after the
door was opened automatically but before
the actual cycle end.
Make sure the cycle has ended before starting to unload the dishes (see DAILY USE).
For even better drying results, it is recommended to let the dishes sit inside the dish-
washer with the door open for additional 15 minutes after the cycle ends.
The dishes are sitting too at.
If you notice puddles of water inside cavities of cups, mugs or bowls, try loading the
dishes (especially in the upper rack) providing more inclination to let larger amounts
of water drip down before drying starts.
The selected cycle does not have the dry-
ing phase.
Please check in the PROGRAMS TABLE if the selected program is equipped in the
drying phase.
Acycle without the drying phase may not deliver desired drying eciency, so it is
recommended to change cycle selection for the one that has the drying phase.
The dishes are made of non-stick or plastic. Some water drops remaining on this type of material are normal.
Dishes and glass-
es are covered
with limescale or
a whitish lm.
The salt reservoir is empty.
Rell the reservoir with salt as soon as possible. Using the appliance without salt may
cause damage to its internal components.
The water hardness setting is too low.
Increase the setting (see WATER HARDNESS TABLE).
The cap of the salt reservoir is not properly
closed.
Check and close the salt reservoir cap.
The rinse aid reservoir is empty or the rinse
aid dosage is insucient.
Rell the dispenser with rinse aid and check the dosage setting (for more information
- see FILLING THE RINSE AID DISPENSER).
The dishwasher
shows F8 E5
Valve is blocked or faulty. Close the water tap, if possible. Do not switch o the power supply. Call the service.
Detergent leaks.
Depends on the liquid detergent used and
can be emphasized in case of delay option
is activated.
Small leaks will not cause machine malfunction and can be avoided by changing
liquid detergent type or using tablets.
TROUBLESHOOTING
Please scan the QR code on your product in order to have more detailed information.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.hotpoint.eu and parts-selfservice.europeanappliances.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product’s identication plate.
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu.
IEC 436
:
Bekijk gratis de handleiding van Hotpoint HA6IB16B2M6L0, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hotpoint |
| Model | HA6IB16B2M6L0 |
| Categorie | Vaatwasser |
| Taal | Nederlands |
| Grootte | 4421 MB |
