Hoshizaki FS-1022MLJ-C handleiding
Handleiding
Je bekijkt pagina 29 van 38
29
J. Alarm Safeties
Should an alarm occur, follow the instructions in the table below to address the alarm.
If an alarm continues to occur, contact an authorized service agent.
In case of alarm, the built-in safeties shut down the unit, the orange "ALARM" LED
turns on, and audible alarms sound as listed below.
No. of Beeps
(every 5 sec.)
Type of Alarm Reset Options
1 Low Water Safety
UFS open>90 sec. after WV energized.
Automatic reset once water supply is restored
and UFS closes.
2 Control Switch
In "DRAIN" position longer than 15 min.
Automatic reset once the control switch is moved
to the "ICE" position.
3 High-Pressure Switch
First and second activation in 1 hr.
Automatic reset once pressure drops below the
high pressure threshold and the high pressure
switch closes.
4 High-Pressure Switch
Third activation in 1 hr.
Call for service. To avoid possible catastrophic
failure, it is recommended to leave the icemaker
off until this alarm is resolved. Manual reset. Turn
power off and on again.
5 Freeze Timer
WV off > 30 min. since last WV activation.
Call for service. Manual reset. Turn power off and
on again. Check for FS stuck (up), WV leaking by,
TXV defective, LLV not opening, low charge, HM
not bypassing, or inefficient Comp.
6 Low Voltage
92VAC±5% or less
Green "POWER" LED turns off if voltage
protection operates.
Control voltage safeties automatically reset when
voltage is corrected.
7 High Voltage
147VAC±5% or more
8 a) Gear Motor Fuse or
Protector Open
CCR contacts fail to close.
Used on all models.
Turn power off. Check for GM fuse or protector
open. Replace fuse or let protector cool and
reset.
If persistent trips occur, call for service.
b) Evaporator Thermistor
At GM startup Evaporator
thermistor
<
-4°F (-20°C).
Used on cubelet (-C)(-SC)(-CB)
models only.
Turn power off. Call for service.
To avoid possible catastrophic failure, it is
recommended to leave the icemaker off until this
alarm is resolved.
Manual reset. Turn power off and on again.
9 Bin Control 2 (Mechanical)
Open Circuit Control Board K8
(#3 and #4)
Not used on DCM or
self-contained models.
Manual reset. Turn power off and on again.
Modular Flaker and Cubelet (-C)(-SC)(-CB)
Models:
Control Board S2 Dip Switch #7 must be ON.
DCM and Self-Contained Models:
Control Board S2 Dip Switch #7 must be OFF.
10 Evaporator Thermistor
Evaporator thermistor reaches
-22°F (-30°C) for 3 consecutive cycles.
Used on cubelet (-C)(-SC)(-CB)
models only.
Turn power off. Call for service.
To avoid possible catastrophic failure, it is
recommended to leave the icemaker off until this
alarm is resolved.
Manual reset. Turn power off and on again.
Legend: CCR–compressor control relay; FS–oat switch; GM–gear motor;
HM–headmaster (C.P.R.); LLV–liquid line valve; SLV–suction line valve;
TXV–thermostatic expansion valve; UFS–upper oat switch; WV–inlet water
valve
Dip switches are factory set and must be adjusted per the unit's service manual or
Hoshizaki Technical Support recommendation.
Bekijk gratis de handleiding van Hoshizaki FS-1022MLJ-C, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hoshizaki |
| Model | FS-1022MLJ-C |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3317 MB |
