Handleiding
Je bekijkt pagina 14 van 152
14
GB
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Manual cleaning
• Clean the cooled exterior and interior surface with a cloth or
sponge slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be
-
fore and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for clean
-
ing. Do not use petrol or solvents!
• No parts are dishwasher safe.
• Clean fan with appropriate descaling detergents to ensure
creating limescales.
• Remove door gasket and wash it separately with warm soapy
water, then rinse and dry with soft cloth.
Semi-automatic cleaning
• Apply a suitable detergent to the chamber walls, fan covers
and the inner door glass. Leave for about 20 minutes.
• Set the temperature to about 100-120°C and the humidifica
-
tion level to position 5. Set the time to 15 minutes.
• After the cycle is finished, open the door and wait for the ap
-
pliance to cool down. Rinse with water.
• To dry the chamber, set the cycle to 10 minutes and the tem
-
perature to about 180-200°C (repeat the cycle if necessary).
• After cleaning, leave the door slightly open.
Maintenance
• Check the operation of the appliance regularly to prevent se
-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car
-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis
-
connect the appliance from power supply when moving and
hold it at the bottom.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problems Possible cause Possible solution
Appliance
does not work
(control panel
totally off).
Faulty connection to
the power mains.
Check connection to
the power mains.
Lack of voltage. Restore the power
supply voltage.
Blown electronic
board protection
fuse.
Contact with technical
service.
Cooking cycle
active - appli
-
ance does not
work.
Door open. Close the door
properly.
Door sensor dam
-
aged.
Contact with technical
service.
Humidification /
steam produc
-
tion does not
work.
Faulty water con
-
nection.
Check connection to
the water mains.
Closed water valve. Open the valve.
Obstructed water
inlet filter.
Clean the filter.
Damaged water inlet
solenoid valve.
Contact with technical
service.
Door closed.
Steam escape
through the
gasket.
Gasket mounted not
properly.
Check gasket as
-
sembly.
Damaged gasket. Contact with technical
service.
Handle adjusted
incorrectly.
Non evenly
cooking.
One of the motor is
faulty or operates at
low speed.
Contact with technical
service.
The motors do not
reverse direction.
Heating elements
damaged.
Internal lamp
does not work.
Lamp damaged Replace bulb.
Safety thermal
protection
activated contin
-
uously.
Damaged thermal
protection.
Contact with technical
service.
Control thermostat
damaged.
Error code identification
Error codes Possible cause Possible solution
E01: Chamber
probe not
detected.
Interrupted connection
between probe and
electronic plate.
Contact with
technical service.
Chamber probe damaged.
E02: Core probe
not detected.
Interrupted connection
between probe and
electronic plate.
Contact with
technical service.
Core probe damaged.
E03: Power
supply blackout.
Lack of main power in
period of time.
Reactive inter
-
rupted cycle.
E04: USB error USB not detected/reada
-
ble/ damaged.
Replace USB
drive.
Interrupted connection
between USB port and
electronic plate.
Contact with
technical service.
Bekijk gratis de handleiding van Hendi 219942, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hendi |
| Model | 219942 |
| Categorie | Oven |
| Taal | Nederlands |
| Grootte | 24851 MB |
