Hazet 7295-2STAC handleiding
Handleiding
Je bekijkt pagina 31 van 100
31
Faults
1. Faults
Message Reason Action
Nothing shown on display No rechargeable battery inserted, battery
inserted incorrectly or battery is discharged
Insert new, fully charged rechargeable battery correctly
(see 7, Commissioning)
Nothing shown on display If a new, charged battery is correctly inserted
and nothing appears on the display after
switching on by pressing
(3 sec. until
acoustic signal sounds twice), the torque
wrench with built-in angle gauge is defective.
Send the torque wrench with built-in angle gauge to
your HAZET partner for testing.
"System test not OK" An electronic system test runs at power-on. If
the torque wrench with built-in angle gauge is
under load when switched on, the message
"System test not OK" is displayed.
Switch the torque wrench with built-in angle gauge off
by pressing
. Place the torque wrench with built-in
angle gauge on a flat, stable surface such that no
loading is applied to it. To switch on the torque wrench
with built-in angle gauge, re-press
(3 sec. until
acoustic signal sounds twice).
"System test not OK" If it is certain that the torque wrench with
built-in angle gauge was not under any load
when switched on, and "System test not
OK" is displayed nevertheless, the torque
sensors are not working properly (e.g. fol
-
lowing overloading).
Send the torque wrench with built-in angle gauge to
your HAZET partner for testing.
"Service" If "Service" is displayed after switching on the
torque wrench with built-in angle gauge, this
is an indication that 5000 load cycles have
been performed since the last calibration.
If you wish to ignore this message, press
and
at the same time. Work can continue immediately. This
message continues to be displayed every time the
device is switched on.
Send the torque wrench with built-in angle gauge to
your HAZET partner for calibration.
The direction of rotation, the
torque target value and the
tolerance specification (in %)
are not displayed when swit
-
ched on.
You are in mode "Track torque" You are able to work in program "Track torque".
You are able to change the torque program. Refer to
Section 8, Programming
No value is displayed upon
operating the torque/angle
wrench.
You are on the start display. "OK" is
displayed.
Check the settings carefully. Confirm the settings
by pressing
. "OK" is no longer displayed. The
torque wrench with built-in angle gauge is ready
to use.
Torque or rotation angle value
not OK (alternately)
The torque or rotation angle value applied
was not within the programed tolerance of
the target value. The torque or rotation angle
value was too low. No, or only the first, signal
level was activated during operation.
Proceed in line with the instructions for this screw-joint:
e.g. undo the screw and re-tighten it, or replace it with
a new one.
Carefully increase the torque. Pay attention to the actu
-
ation speed and the signal levels. Operate the torque
wrench with built-in angle gauge in such a way that it
remains in the 2nd signal level.
Torque or rotation angle value
not OK (alternately)
The torque or rotation angle value applied
was not within the programed tolerance of
the target value. The torque or rotation angle
value was too high. The 3rd or 4th signal level
was activated during operation.
Proceed in line with the instructions for this screw-joint:
e.g. undo the screw and re-tighten it, or replace it with
a new one.
Reduce the actuating force. Pay attention to the actu
-
ation speed and the signal levels. Operate the torque
wrench with built-in angle gauge in such a way that it
remains in the 2nd signal level.
Bekijk gratis de handleiding van Hazet 7295-2STAC, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hazet |
| Model | 7295-2STAC |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 16813 MB |
