Hazet 2191/12K handleiding
Handleiding
Je bekijkt pagina 4 van 4
223113 V cb/pdf
DIN F flares
Clamp the basic unit (2) into the vice with the
gripping piece.
Then push the gripping jaw (3) into the basic unit
(2) so that the side with the inscription „180°“ (on
older gripping jaws the inscription is „F“) faces
upwards.
Open the gripping jaw (3) and allow the tube to
be flared to protrude a few millimetres at the top.
The base block (5) now serves as a setting gau
-
ge. Using the base block (5), push the tube down
to the gripping jaw (3) with the recess facing
downwards. Close the gripping jaw (3).
9. Application
Precondition for a tight flare is a clean deburring of the inner and outer tube rims. For this purpose,
use the pipe deburring tool 2191-2.
Plug the pressure piece, which has been made
slippery and corresponds to the tube diameter,
onto the tube. Place the base block (5) on it with
the opening facing downwards. Then push the
gripping jaw (3) into the tool until the tube end
with the thrust block and base block (5) is under
the pressure spindle.
Ensure that the locking point locks audibly
into place in the intended notch of the
gripping jaw.
Make sure that the pressure spindle is positioned
centrally above the brake line.
Turn the clamping spindle.
Turn down the pressure spindle. The thrust block
and base block (5) form the „F“ flare.
DIN E flares
• Prepare as described under 1-6, for completion turn the
gripping jaw (3) so that the side with the inscription „90°“ (on
older gripping jaws the inscription is „E“) faces upwards and
reinsert the gripping jaw (3). Clamp the flare again and finish
machining with the 90° pressure piece (12).
D flares (90°)
• Insert the gripping jaw (3) so that the side with the inscription
„90°“ (on older gripping jaws, the inscription is „E“) faces
upwards. Produce as described under 1 - 6 using the 90°
pressure piece (12).
180° flares
• Produce as D flare (90°), to complete turn and insert the
gripping jaw (3) so that the side with the inscription „180°“
(on older gripping jaws the inscription is „F“) faces upwards.
Clamp the flare again and press it flat with the back of the
base block (5).
SAE F flares
• Insert the gripping jaw (3) so that the side with the inscription
„90°“ (on older gripping jaws, the inscription is „E“) faces
upwards. Produce as described under 1 - 6.
@@
””
££
fifi ^^
##
HAZET-WERK Hermann Zerver GmbH & Co. KG
•
}
10 04 61 • 42804 Remscheid • GERMANY
;
Güldenwerther Bahnhofstraße 25 - 29 • 42857 Remscheid • GERMANY
[
+49 (0) 21 91 / 7 92-0 •
\
+49 (0) 21 91 / 7 92-375 (National) -400 (International) •
^
hazet.de •
]
info@hazet.de
10. Storage
The tool has be stored according to
the following conditions:
• Keep tool in a dry and dust-free place.
• Do not expose the tool to liquids or aggressive substances.
• Do not store the tool outdoors.
• Keep the tool out of reach of children.
• Storage temperature: -10°C up to +45°C
• Relative air humidity: max. 65%.
11. Maintenance and Cleaning
• Do not let the tool set fall down. Do not expose to impacts
or liquids as they might impair the functional efficiency and
damage the tool set.
Bekijk gratis de handleiding van Hazet 2191/12K, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hazet |
| Model | 2191/12K |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4512 MB |
