Haws 3612 handleiding
Handleiding
Je bekijkt pagina 2 van 11
09/21 Models 3613612F Page 2 of 11
RECOMMENDED TOOLS:
- Measuring Tape
- PVC Pipe Cutter
- Plastic Tubing Cutter
- PVC Solvent Weld Glue
- ¼” Bit-Holding Screwdriver
- Level
- 10” Pipe Wrench
- Adjustable Plier
- 1/8 and 5/32 Tamper Resistant Hex Bits (Supplied)
- 9/16” and 5/8” Box/Open Combination Wrenches, 8” Max Length
- 3/8” Socket Wrench/Rachet, 8” Max Length
- 9/16” Deep Socket
- 15/16” Socket
LOCATION OF UNIT: The Model 3612/3612F (with Filter) Bottle Filler and Dual Fountain can
be installed and assembled to be ADA accessible by first locating the pedestal base with at
least 8 inches of clear unobstructed hardscape behind the pedestal. Provide hardscape that
is at least 74 inches wide. When the right pedestal arm is installed in the high orientation, the
height dimensions shown on the model specification sheet meet current Federal Americans
with Disabilities Act (ADA) wheelchair requirements. When the left pedestal arm is installed in
the highest position, the height dimensions shown on the model specification sheet meet
current ADA standing height requirements. The bottle filler meets ADA requirements for either
a front approach or a side approach. When installing this unit, local, state and federal
(including ADA) codes must be adhered to. If height other than shown is required, then
dimensions must be adjusted accordingly.
ATTENTION: For model 3612F (model with Filter), the Operating Temperature Range for the
6477 Filter Kit Assembly (Required - supplied separately) is 40° F - 100° F (4.4° C – 37.8° C).
SUPPLY LINE: Model 3612 – The minimum recommended line size is 1/2“IPS with 30-90 psi
(2-6 ATM) flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended. Model 3612F (with Filter) – The minimum recommended line size is 1/2“IPS
with 40-90 psi (2.76-6 ATM) flowing pressure.
PLUMBING CONNECTIONS: Model 3612 – Water supply inlet connection is a 3/8“O.D.
compression fitting. Waste outlet is 1-1/2” PVC pipe. Model 3612F – Water supply inlet and
outlet connection (for Filter) is a 3/8“O.D. push-in type fitting. Waste outlet is 1-1/2” PVC pipe.
Plumbing connections will vary depending on how each model is configured during assembly.
Please consult the installation drawings below for supply and waste fitting arrangements and
assembly for your specific model.
MAINTENANCE: Models 3612 & 3612F Periodically clean the pushbutton valve strainer.
Refer to 5874 Series Valve Operation and Maintenance Manual for more information. Model
3612F – Filter replacement to occur at 1 year maximum or 3,000 gallons maximum, whichever
comes first. Replace filter per Filter Replacement instructions listed on model 6477 Operation
& Maintenance Manual.
INSTALLATION PROCEDURE
GENERAL NOTES:
1. For all compression fitting connections, only connect NSF-61 copper or plastic
3/8” outside diameter tubing. The following assembly instructions must be
followed to ensure a watertight connection:
Bekijk gratis de handleiding van Haws 3612, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Haws |
| Model | 3612 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1576 MB |
