Haws 1212SFH handleiding
Handleiding
Je bekijkt pagina 4 van 21
9/21 1200 S
eries Electric Water Coolers Page 4 of 21
C. INSTALLATION OF HIGH-SIDE (LEFT) WATER COOLER
23. Remove the hanger bracket from the back of the cooler by removing (1) screw.
24.
With the cooler laying on its back, remove the (4) screws holding the skirt to the bottom of the frame. Then remove th
e
skirt by sliding the skirt away from
the cooler.
25.
Mount the hanger bracket on the wall using (4) 1/4” structural screws, in accordance with the installation drawing.
a. NOTE: The screws must engage into structural material such as concrete, metal backing, wood blocking, etc.
DO NOT use drywall anchors.
b. NOTE: The hanger bracket has a notch indicating the centerline of the water cooler.
26.
Using cutting pliers, cut the cable-tie holding the unconnected wires in the upper left side of the refrigerated cooler. These
wires will supply power, signal, and ground to the high side water cooler. Take care not to damage the wires when cutt
ing
the tie.
27.
Remove the protective plastic wrap from the feedthrough cover.
28. Feed the water tubing and wiring through the feedthrough cover. Install the feedthrough cover by sliding its upper right
tab behind the edge of the black cap of the right side water cooler (see installation drawing). Use a bubble level to ensure
the left edge of t
he feedthrough cover is vertical. Secure with a 1/4” or #10 screw.
a.
NOTE: Installing the screw into structural material is recommended. Toggle bolts or
drywall anchors can be
used but they ma
y make the unit more susceptible to damage from
vandals.
29.
Hang the cooler onto the hanger bracket.
a. NOTE: The bracket must go through the holes in the cooler frame that are shaped like a sideways letter “P”.
b. NOTE: The bracket allows for some lateral adjustment of the cooler location. Slide the cooler laterally until it
touches the side of the feedth
roug
h cover.
30.
Secure both the lower right and lower left ends of the cooler to the wall using at least (2) 1/4” or 3/8” structural screws
.
These screws should go throu
gh the holes which are approximately 5” from the bottom of the cooler.
Washers may be
required.
a. NOTE: The screws must engage into structural material such as concrete, metal backing, wood blocking, etc.
DO NOT use drywall anchors.
31.
Route the drain hose from the left unit to the right unit. Attach to the open branch of the drain tailpiece using the supp
lied
hose clamp, ensuring that the d
rain hose slopes downward over its entire length.
32.
Attach the 3/8” water supply line to the 3/8” connec
tor in the left side unit.
33.
Connect the wire connector in the left unit.
34. Remove the green ground screw from its hole in the left unit and use it to secure the green ground wire to that same
location.
35.
Snap wires into the plastic wire clip (near the ground screw) to keep them away from the sheet metal e
dges.
D. START-UP
36. Open the water supply valve and check the system for leaks.
37. Plug the power cord into the wall receptacle (which should presently be powered off at the breaker panel). Check that
all
wiring is fully
contained within the unit and that no wires are impeding fan blade movement.
38.
Peel back the protective plastic from the back flanges and top 1” of
the skirt(s).
39.
Taking care not to scratch the black plastic parts behind the bowl, reinstall the skirt(s). Finish removing the protective
plastic from the skirt(s).
40. Reconnect power at the breaker panel, then place a cup over the bubbler (to minimize splattering) and push the front
button to activate the bubbler flow.
Keep the button depressed until all air is purged out of the wate
r line.
a.
NOTE: If the unit has a filter, run the bubbler for 10 minutes in order to properly flush the filter.
41.
If a bottle filler has been installed, place a cup under the nozzle of the bottle filler and run the water until the air ha
s been
purged out of the water line.
42. If a high/low unit has been installed, place a cup over the bubbler of the second unit and push the front button to activate
the bubbler flow. Keep the button depressed until the air has been purged out of the water line.
43.
The stainless steel panels can be cleaned with the provided cleaning wipe. Buff off excess with a clean cloth or pape
r
towel. Do not all
ow the cleaning fluid to t
ouch the plastic parts or the bottle filler.
44.
After allowing a few minutes for the water to cool down, enjoy a cold drink of water.
E. OPTIONAL PROGRAMMING INSTRUCTIONS (BOTTLE FILLER UNITS ONLY)
To enter programming mode, remove the clear cover underneath the bowl, and hold the button until the up/down arrow
keys and “select” appear on the bottle filler display. Programming mode enters at the top-level menu. In general, the
up/down arrows and select keys work as follows;
Up/Down Arrows – Cycle through the top-level menu items or
values in the programmable fields
Select – enters programming of the associated top-level menu
item, or sets value and advances to next programmable field, or
programs value (indicated by value flashing) prior to returns to the
main menu
Programming the Haws 12 Electric Water Cooler through the bottle
willer user interface is intuitive. However, the following Electric
Water Cooler and Bottle Filler Programming Table can be used as
a guide while programming the unit, which are retained during
power outages.
Replace the clear plastic cover after programming the unit.
Figure 3: Programming Mode Button
viewed from underside of bowl
Bekijk gratis de handleiding van Haws 1212SFH, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Haws |
| Model | 1212SFH |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3610 MB |
