Handleiding
Je bekijkt pagina 11 van 40
English
Form No. IRNGCDM-1020
11
2. Cut and drill the appropriate holes in the vertical surface
where the control enclosure will be installed. Refer to
the “Installing the Control Panel” procedure for cutout
dimensions.
3. Cut the required openings in the cabinetry to provide proper
ventilation to the induction range. Refer to the “Ventilation
Requirements” listed previously in this section.
4. If necessary, make structural modifications or add bracing
underneath the countertop to ensure the countertop will
support the weight of the unit and its contents.
NOTE: The countertop must be level to ensure proper operation
of the Induction Range.
5. Apply a bead of NSF-approved silicone sealant onto the
countertop material around the cutout opening.
NOTE: The silicone sealant must be rated for use at
temperatures up to 250°F (121°C)
6. Install the trim ring into the countertop opening.
7. Carefully lower the unit into the trim ring, making sure the
power cord and control cable do not get pinched.
Silicone
Front of Unit
Countertop
Trim
Ring
Cutaway view of trim ring.
Standard Trim Ring Installation
8. Apply a bead of NSF-approved silicone sealant in the gap
between the trim ring and the induction range.
a. Make sure the unit is centered in the trim ring.
b. Install masking tape on each side of the gap to define the
edge of the sealant.
c. Carefully apply sealant into the gap.
d. Quickly smooth the sealant surface.
e. Carefully remove the masking tape before the sealant
dries.
NOTE: The silicone sealant must be rated for use at
temperatures up to 250°F (121°C)
9. Install the control panel in the desired location. Refer to the
“Installing the Control Panel” procedure.
10. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
• A Welcome Screen will appear on the Control Display for
a few seconds, then the display will go blank.
Installing the Control Panel
Use the following procedure to install the control panel.
WARNING
Remote mounted control panel must be mounted on a
vertical wall and installed in vertical position. Mounting
control panel in horizontal position may result in collection
of liquids and lead to an electric shock.
1. Carefully measure and cut the opening in the cabinet wall
for the control panel.
2. Drill the appropriate holes around the cutout for the control
panel mounting screws (not supplied).
6″
(150 mm)
13″
(330 mm)
Cabinet Wall
Cabinet Wall
5-1/2"
(140 mm)
1"
(25 mm)
6-3/8"
(162 mm)
3/16"
(6 mm)
3/16"
(6 mm)
Silicone Sealant
Control Panel Cutout and Screw Hole Dimensions
3. Apply a 1/4″ (6 mm) bead of NSF-approved silicone sealant
where the trim on the control panel will contact the cabinet
surface. Refer to the “Control Panel Cutout and Screw Hole
Dimensions” illustration for silicone placement.
4. Position the control panel into the cutout opening through
the front of the cabinet. Make sure to embed the trim on the
control panel into the silicone.
5. Fasten the control panel to the vertical surface using six
mounting screws (not supplied).
6. Connect the front and back male control cables on the
control panel to the corresponding female control cables
on the induction range.
Mounting Screw
Control
Cables
(male)
Silicone
Sealant
Cabinet Wall
Cabinet Wall
Installing the Control Panel
INSTALLATION
Bekijk gratis de handleiding van Hatco Rapide Cuisine IRNG-PB2-29, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hatco |
| Model | Rapide Cuisine IRNG-PB2-29 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 7062 MB |
