Handleiding
Je bekijkt pagina 5 van 37
T1
T2
T3
L2-L3
L1
T1= ON /OFF motor.
Short and repeated pressings of the T1 key result in
cyclical passing to the control of the suction speed (power).
Each speed corresponds to lighting up of the respective
LED:
- 1st speed (LED L1 fixed white light)
- 2nd speed (LED L1 fixed white light)
- 3rd speed (LED L1 fixed white light)
- Intensive (LED L1 flashes white light), the intensive
speed is timed and lasts 5 minutes, at the end of which the
hood goes to 3rd speed.
- The hood motor can be switched off by pressing the T1
button for 3 seconds. CAUTION! The automatic VOC
function must not be active.
To switch off the hood during the automatic VOC function,
follow the instructions for deactivating of the VOC function.
T2= Adjusts the light temperature (long press).
- The default light colour tone is set to 50% (neutral).
To adjust, with the light on, hold down the T2 key for a few
seconds. The L2 and L3 LEDs will flash orange. Releasing
the T2 key the desired light tone will be set and the L2 and
L3 LEDs will return to fixed and white.
Please note! Unplugging the power cord from the outlet,
the tone is restored.
T3= Light ON/OFF button (short press) / Adjusts the
intensity of the light (long press).
- The default light intensity is set to 100% (intense).
For adjustment, with the light on, hold down the T3 key for
a few seconds, the L2 and L3 LEDs will flash white.
Releasing the T3 key the desired light intensity will be set
and the L2 and L3 LEDs will return to fixed and white.
Please note! Once the hood is turned off, the light intensity
setting is restored.
VOC sensor calibration
Calibration is necessary to allow the sensor with which the
hood is equipped to work correctly and can be Automatic
(before installation or after a power failure) or Manual (if
automatic operation is not satisfactory).
Automatic Calibration: starts with the motor off whenever
the hood is reconnected to the electricity mains. LED L1
flashes blue for 5 minutes, accompanied by a short
acoustic signal (Beep), at the end of which LED L1 starts
flashing white accompanied by a long acoustic signal
(Beep) which signals the end of the automatic calibration.
Manual Calibration: to be performed when unsatisfactory
functioning of the automatic operation is perceived and it
must be performed when normal environmental conditions
persist in the kitchen.
Manual calibration is activated by holding down key T1 for
10 seconds. LED L1 flashes blue followed by an acoustic
signal (short beep), LED L1 flashes for 5 minutes, at the
end of which LED L1 starts flashing white accompanied by
a long acoustic signal (Beep) which signals the end of the
manual calibration.
At the end of the calibration L1 will flash slowly in
dimmed mode in WHITE to indicate successful
activation. The motor will activate automatically if
vapours/fumes are detected.
Activation and deactivation of the VOC function
Keeping the T1 key pressed for 5 seconds activates or
deactivates the VOC sensor function.
- By pressing the T1 key the VOC function is activated, the
L1 LED turns white and flashes. The hood will turn on at
the most suitable speed based on the cooking fumes
detected by the sensor it is equipped with.
To disable it, follow the same procedure.
Grease filter warning
After 40 hours of operation the LED L1 L2 L3 are red and
fixed.
When this warning appears, it means that the installed
grease filter needs to be washed. To reset the signal, keep
the T1 and T3 keys pressed for 3 seconds. To confirm the
reset, all the L1-L2-L3 LEDs flash red twice and the hood
emits a long beep.
Carbon filter warning
After 160 hours of operation, the LED L1 (fixed red LED),
L2 and L3 start flashing red. When this warning appears, it
means that the installed carbon filter needs to be replaced.
To reset the signal, keep the T1 and T3 keys pressed for 3
seconds. To confirm the reset, all the L1-L2-L3 LEDs flash
red twice and the hood emits a long beep.
In standard mode, the carbon filter warning is not
active.
If the hood is used in the filter version, it is necessary to
enable the carbon filter warning.
Carbon filter warning activation:
Keeping keys T1 and T2 pressed simultaneously with the
hood off, the alarm for the saturation of the filters is set,
therefore first LED L1 turns on (red) then also L2 and L3
(red) after which a long beep will follow and the LEDs L2
and L3 flash briefly to indicate successful activation.
Carbon filter warning deactivation:
Repeat the operation described above. First LEDs L1, L2
and L3 light up at the same time then only L1, after which a
long beep will follow and LEDs L1, L2 and L3 light up again
4
Bekijk gratis de handleiding van Haier HAPY6CBS6BVOCLC, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Haier |
| Model | HAPY6CBS6BVOCLC |
| Categorie | Afzuigkap |
| Taal | Nederlands |
| Grootte | 4560 MB |
Caratteristiche Prodotto
| Soort bediening | Touch |
| Kleur van het product | Zwart |
| Ingebouwd display | Nee |
| Gewicht | 10100 g |
| Breedte | 514 mm |
