Gys BMW C7502655 handleiding
Handleiding
Je bekijkt pagina 51 van 112
51
BMW C7502655 - GYSPOT PTI GENIUS
EN
6
Trigger test on diode ope-
ning and temperature
TRANSFO TEMP = x.xx V ON or OFF Blocking
Overheating of the power transformer. Allow the machine to
cool down before starting up again.
7
Transformer primary
temperature
THICKNESS SENSOR =
xx.x mm
PASS No blocking
8 Position sensor
WELDING VOLTAGE =
x.xx V
PASS No blocking
9 Welding voltage BACKUP CELL = x.xx V PASS or FAIL No blocking
10 Backup battery voltage
AIR PRESSURE = xx.x
bar si PASS
PASS or FAIL Blocking Air pressure sensor from the HS network, contact your dealer.
Network pressure
11 Clamp pressure
GUN PRESSURE = xx.x
bar si PASS
PASS or FAIL Blocking Air pressure sensor of the HS gripper, contact your dealer.
Gun presence detection
12 Détection présence pistolet CONNEXION GUN ON or OFF No blocking
SPOT COUNT
A spot count tool keeps count of the dierent spot weld done using the same cap. If there is no
problem during the welding, the following message is displayed.
The count is displayed at the top left corner of the screen. Press the button
for 2 seconds to
reset the count after changing the caps.
The machine counts the number of points achieved with each arm independently. A warning
message appears on the screen when the limit of the points made by the headings is reached. The
message remains displayed after each point until the counter is reset.
If the caps are not changed after the warning message is displayed and the count is simply reset, they can deteriorate and have a negative
impact on the quality of the weld.
RECORDING FEATURES
The Identication mode is optional and can be activated using the «settings» menu.
If the identication mode is switched o, il sut de saisir un nom de rapport et de l’activer pour mémoriser les points de soudure eectués.
The log allows to store the parameters of the spots made using the clamp. It is available in all the modes by pressing the 2 buttons
and .
The user program is available in all modes by pressing the
and buttons.
Report (log)
Saving a report allows you to retrieve the data of a series of spot made with using the clamp, and to
save them on the memory card so that they can be retrieved from a PC for example. GYS provides
a software called GYSPOT to read the SD card and edit the logs on a PC. This GYSPOT software is
stored on the SD card as well as the user manual.
By default, this feature is disabled when the machine is switched on. Pressing the recording button
(on/o) and the «mode» button starts recording the report in the selected log. Pressing the record
button again (on/o) stops the current recording.
The log created contains: an ID entered by the user, as well as for each spot performed, the tool and arm used, the machine settings (power and
pressure). It also contains the following possible error messages that may have occurred during its recording: I LOW, P LOW, PB CAPS.
The ID is entered using the 4 keys +, -
or . When entering an identier already in use, the machine will record the new points in succession,
without deleting the previous ones.
The button is used to retrieve a previously saved report and read it back on the screen.
The current recording must be stopped by pressing the
button before it can be displayed on the screen. The button is used to exit the
report view mode.
Bekijk gratis de handleiding van Gys BMW C7502655, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Gys |
| Model | BMW C7502655 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 27796 MB |
