Growatt WIT29.9-50K-XHU handleiding
Handleiding
Je bekijkt pagina 119 van 130
Error Code
Description
Suggestion
Error 409
Bus voltage
abnormal
1. Restart the inverter.
2. If the error message persists, please
contact Growatt support.
Error 411
Internal
communication
failure
1. Check the wiring of the
communication board after shutdown.
2. If the error message persists, please
contact Growatt support.
Error 412
Temperature sensor
disconnected
2. If the error message persists, please
contact Growatt support.
1. Check if the temperature sensor
module is properly connected.
Error 413
IGBT drive fault
2. If the error message persists, please
contact Growatt support.
1. Restart the inverter.
Error 414
EEPROM error
1. Restart the inverter.
2. If the error message persists, please
contact Growatt support.
Error 415
Auxiliary power
supply abnormal
1. Restart the inverter.
2. If the error message persists, please
contact Growatt support.
Error 416
DC/AC overcurrent
protection
1. Restart the inverter.
2. If the error message persists, please
contact Growatt support.
Error 417
Communication
protocol mismatch
2. If the error message persists, please
contact Growatt support.
1. Restart the inverter.
Error 418
DSP and COM
firmware version
mismatch
1. Check the firmware version.
2. If the error message persists, please
contact Growatt support.
Error 419
DSP software and
hardware version
mismatch
1. Check the firmware version.
2. If the error message persists, please
contact Growatt support.
Error 421
CPLD abnormal
2. If the error message persists, please
contact Growatt support.
1. Restart the inverter.
Error 422
Redundancy
sampling
inconsistent
1. Restart the inverter.
2. If the error message persists, please
contact Growatt support
Error 423
PWM pass-through
signal failure
2. If the error message persists, please
contact Growatt support.
1. Restart the inverter.
116115
Error Code
Description
Suggestion
Error 425
AFCI self-test failure
2. If the error message persists, please
contact Growatt support.
1. Restart the inverter.
Error 426
PV current sampling
abnormal
1. Restart the inverter.
2. If the error message persists, please
contact Growatt support.
Error 427
AC current sampling
abnormal
1. Restart the inverter.
2. If the error message persists, please
contact Growatt support.
Error 430
EPO fault
1. Restart the inverter.
2. If the error message persists, please
contact Growatt support.
Error 431
Monitoring chip
BOOT verification
failed
1. Restart the inverter.
2. If the error message persists, please
contact Growatt support.
Error 500
BMS failed to
communicate with
the inverter
1. Check the connection of the RS485
cable between the inverter and the
battery.
2. Check if the battery is in the sleep
mode.
3. If the error message persists, please
contact Growatt support.
Error 501
The BMS reports that
the battery failed to
charge/discharge
1. Figure out the fault based on the BMS
error code.
2. If the error message persists, please
contact Growatt support.
Bat Voltage Low
The battery voltage
is below the lower
threshold
2. If the error message persists, please
contact Growatt support.
1. Check the battery voltage.
Error 503
The battery voltage
exceeds upper
threshold
1. Check the battery voltage. If it is
within the permissible range, please
restart the inverter. If not, please
replace the battery.
2. If the error message persists, please
contact Growatt support.
Error 504
The battery
temperature is
beyond the range
for charging /
discharging
2. If the error message persists, please
contact Growatt support.
1. Check the temperature of the battery.
Bekijk gratis de handleiding van Growatt WIT29.9-50K-XHU, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Growatt |
| Model | WIT29.9-50K-XHU |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 16744 MB |
