Growatt SPH 4000-10000TL3 BH-UP handleiding

Niet gecategoriseerd

Growatt

88 pagina's

PDF beschikbaar

Handleiding

6.5.6.2 Setting guide

(1) Long press “enter” to access the "WorkMode" configuration page from the home

page for operating mode settings.

(2) Press “down” or press "up" to access the "ExportLimit" page for export limitation

settings.

(3) The first setting item is "ExportLimit", press “enter” once to enter the editing mode.

(4) Press “up” or “down” to change the selected option, and set it to "ON".

(5) Press "enter" once to confirm your setting and exit the editing mode.

(6) Press “down” once, and go to the next item to set "SingleExport" to ON to enable

independent export limitation for each phase.

(7) Press “enter” once to enter the editing mode.

(8) Press "up" or "down" key to change the selected option and set it to "ON".

(14) Press “down” once to go to the next item to access the "Failsafe" for export

limitation failsafe settings.

(15) Press “enter” once to enter the editing mode.

(21) Press "enter" once to confirm your setting and exit the editing mode.

(17) Press "enter" once to confirm your setting and exit the editing mode.

(12) Press "up" or "down" key to set it to the desired value.

(16) Press "up" or "down" key to set it to the desired value.

(19) Press “enter” once to enter the editing mode.

If the following configuration is not applicable, it goes directly to operation (18).

(20) Press "up" or "down" key to change the setting to "ThEn"(Three-phase Enable).

(9) Press "enter" once to confirm your setting and exit the editing mode.

(10) Press “down” once to go to the next item to set the "PowerRate" – limited feed-in

power in percentage.

(18) Press “down” once to go to the next item "LoadFstCtrl" (Load First Control).

(22) Finally, press "Esc" to exit settings.

(11) Press “enter” once to enter the editing mode.

(13) Press "enter" once to confirm your setting and exit the editing mode.

6.5.7 Export limitation configuration for Czech grid code

6.5.7.1 Setting procedure

Figure 6.34

WorkMode

AutoloopDisplary

WorkMode

ExportLimit

:ON/OFF

SingleExport

:ON/OFF

PowerRate:00%

Failsafe

:ON/OFF

LoadFstCtrl:SiEn

LoadFstCtrl:ThEn

6.5.7.2 Setting guide

(11) Press "enter" once to confirm your setting and exit the editing mode.

If the following configuration is not applicable, it goes directly to operation (18).

(14) Press "up" or "down" key to set it to the desired value.

(12) Press “down” once to go to the next item to set the "PowerRate" – limited feed-in

power in percentage.

(2) Set the inverter mode to “Load First”.

(21) Press “enter” once to enter the editing mode.

(23) Press "enter" once to confirm your setting and exit the editing mode.

(24) Finally, press "Esc" to exit settings.

(5) The first setting item is "ExportLimit", press “enter” once to enter the editing mode.

(6) Press “up” or “down” to change the selected option, and set it to "ON".

1) Set the Czech grid code on ShineBus.

(8) Press “down” once, and go to the next item to set "SingleExport" to ON to enable

independent export limitation for each phase.

(9) Press “enter” once to enter the editing mode.

(13) Press “enter” once to enter the editing mode.

(3) Long press “enter” to access the "WorkMode" configuration page from the home

page for operating mode settings.

(4) Press “down” or press "up" to access the "ExportLimit" page for export limitation

settings.

(7) Press "enter" once to confirm your setting and exit the editing mode.

(10) Press "up" or "down" key to change the selected option and set it to "OFF".

(15) Press "enter" once to confirm your setting and exit the editing mode.

(16) Press “down” once to go to the next item to access the "Failsafe" for export

limitation failsafe settings.

(17) Press “enter” once to enter the editing mode.

(18) Press "up" or "down" key to set it to the desired value.

(19) Press "enter" once to confirm your setting and exit the editing mode.

(20) Press “down” once to go to the next item "LoadFstCtrl" (Load First Control).

(22) Press "up" or "down" key to change the selected option to "SIEn"(Single-phase

Enable).

Note: For details of the three export limitation modes, please see Section 6.4.

6463

Bekijk gratis de handleiding van Growatt SPH 4000-10000TL3 BH-UP, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.