Growatt SPH 4000-10000TL3 BH-UP handleiding

Niet gecategoriseerd

Growatt

88 pagina's

PDF beschikbaar

Handleiding

dry contact function by setting "D-Time". When you set D-Export Power to enable the

dry contact function, the dry contact function may not work properly.

2. In the shinemaster parallel system, using the "Heater" option, you can only start the

1. The D-Bat setting item in the generator option will display different parameters

according to the type of battery connected. Min.SOC will displayed when a lithium

battery is connected, and Min.Vbat when a lead-acid battery is connected.

Note:

Chart 6.31

10. In the "Default" menu, you can press Enter to access the setting menu:

"Default set" means that all predefined parameters will be restored to the default value.

Please be cautious not to accidentally choose factory reset.

6.5.5 Three-phase total export limitation configuration

6.5.5.1 Setting procedure

Figure 6.32

Default Set

WorkMode WorkMode

YES

Press “enter” key to

make sure

Press “enter” key more

than 3 seconds to make sure

WorkMode

AutoloopDisplary

WorkMode

ExportLimit

:ON/OFF

SingleExport

:ON/OFF

PowerRate:00%

Failsafe

:ON/OFF

LoadFstCtrl:SiEn

LoadFstCtrl:ThEn

6.5.5.2 Setting guide

(7) Press “enter” once to enter the editing mode.

(1) Long press “enter” to access the "WorkMode" configuration page from the home

page for operating mode settings.

(2) Press “down” or press "up" to access the "ExportLimit" page for export limitation

settings.

(3) The first setting item is "ExportLimit", press “enter” once to enter the editing mode.

(4) Press “up” or “down” to change the selected option, and set it to "ON".

(5) Press "enter" once to confirm your setting and exit the editing mode.

(6) Press “down” once, and go to the next item to set "SingleExport" to ON to enable

independent export limitation for each phase.

(8) Press "up" or "down" key to change the selected option and set it to "OFF".

(11) Press “enter” once to enter the editing mode.

(12) Press "up" or "down" key to set it to the desired value.

If the following configuration is not applicable, it goes directly to operation (18).

(9) Press "enter" once to confirm your setting and exit the editing mode.

(14) Press “down” once to go to the next item to access the "Failsafe" for export

limitation failsafe settings.

(15) Press “enter” once to enter the editing mode.

(16) Press "up" or "down" key to set it to the desired value.

(13) Press "enter" once to confirm your setting and exit the editing mode.

(17) Press "enter" once to confirm your setting and exit the editing mode.

(18) Press “down” once to go to the next item "LoadFstCtrl" (Load First Control).

(19) Press “enter” once to enter the editing mode.

(21) Press "enter" once to confirm your setting and exit the editing mode.

(22) Finally, press "Esc" to exit settings.

(10) Press “down” once to go to the next item to set the "PowerRate" – limited feed-in

power in percentage.

(20) Press "up" or "down" key to change the setting to "ThEn"(Three-phase Enable).

6.5.6 Three-phase independent export limitation configuration

6.5.6.1 Setting procedure

Figure 6.33

WorkMode

AutoloopDisplary

WorkMode

ExportLimit

:ON/OFF

SingleExport

:ON/OFF

PowerRate:00%

Failsafe

:ON/OFF

LoadFstCtrl:SiEn

LoadFstCtrl:ThEn

6261

Bekijk gratis de handleiding van Growatt SPH 4000-10000TL3 BH-UP, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.