Handleiding
Je bekijkt pagina 24 van 35
19
button
button
button
button
Under cool or heat mode, press this button to turn
to quick cool or quick heat mode. " " icon is
displayed on remote controller. Press this button
again to exit turbo function and " " icon will
disappear.
If start this function, the unit will run at super-high
fan speed to cool or heat quickly so that the ambi-
ent temperature approaches the preset tempera-
ture as soon as possible.
Press this button can select left & right swing angle.
Fan blow angle can be selected circularly as below:
●
●
●
●
Press "▲" or "▼" button once increase or dec-
rease set temperature 1°C(°F). Holding "▲" or "▼"
button, 2s later, set temperature on remote control-
ler will change quickly. On releasing button after
setting is finished, temperature indicator on indoor
unit will change accordingly. (Temperature can't be
adjusted under auto mode)
When setting TIMER ON, TIMER OFF or CLOCK,
press "▲" or "▼" button to adjust time. (Refer to
CLOCK, TIMER ON, TIMER OFF buttons).
" " may not be available. When air condi-
tioner receives this signal, the air conditioner will blow
fan automatically.
Press this button continuously for more than 2s, the
main unit will swing back and forth from up to down,
and then loosen the button, the unit present position
of guide louver will be kept immediately.
Under up and down swing mode, when the status is
switched from off to , if press this button again 2s
later, status will switch to off status directly; if
press this button again within 2s, the change of swing
status will also depend on the circulation sequence
stated above.
●
●
●
、 、
When selecting " ", air conditioner is blowing
fan automatically. Horizontal louver will automat-
ically swing up & down at maximum angle.
When selecting " ", air condition-
er is blowing fan at fixed position. Horizontal
louver will stop at the fixed position.
When selecting " ", air conditioner is
blowing fan at fixed angle. Horizontal louver will
send air at the fixed angle.
Hold " "button above 2s to set your required
swing angle. When reaching your required
angle, release the button.
no display
(horizontal louvers
stops at current position)
、 、 、 、
、 、
Press this button, can select Sleep 1 ( ), Sleep 2
( ), Sleep 3 ( ) and cancel the Sleep, circulate
between these, after electrified, Sleep Cancel is de-
faulted.
button
Press this button can select up & down swing angle.
Fan blow angle can be selected circularly as below:
NOTE
NOTE
no display
(stops at
current position)
●
●
Press this button continuously more than 2s, the main
unit will swing back and forth from left to right, and
then loosen the button, the unit will stop swinging and
present position of guide louver will be kept immedi-
ately.
Under left and right swing mode, when the status is
switched from off to , if press this button again
2s later, status will switch to off status directly; if
press this button again within 2s, the change of swing
status will also depend on the circulation sequence stat-
ed above.
The function is only available for some models.
●
Sleep 1 is Sleep mode 1, in Cool modes; sleep sta-
tus after run for one hour, the main unit setting tem-
perature will increase 1 , two hours, setting temper-
ature increased 2 , then the unit will run at this set-
ting temperature; In Heat mode: sleep status after
run for one hour, the setting temperature will de-
crease 1 , two hours, setting temperature will de-
crease 2 , then the unit will run at this setting tem-
perature.
Sleep 2 is sleep mode 2, that is air conditioner will
run according to the presetting a group of sleep tem-
perature curve.
●
●
Bekijk gratis de handleiding van Gree GIH24UZ, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Gree |
| Model | GIH24UZ |
| Categorie | Airco |
| Taal | Nederlands |
| Grootte | 5040 MB |
