Graphite Energy+ 58G098 handleiding
Handleiding
Je bekijkt pagina 11 van 82
11
Chips and dust collect in the guide bar, impeding the free movement of the
chain and negatively affecting lubrication. Clean it periodically when
sharpening or replacing the chain with a thin tool (fig. E1) .
CLEANING THE GEAR COVER
Chips, dust and other contaminants can accumulate under the rack and
pinion cover and adversely affect the operation of the unit. It should be
cleaned periodically (fig. F1) .
CLEANING THE OIL DRAIN HOLE
The oil drain hole can become contaminated, preventing the oil from
distributing properly on the chain and bar. This will negatively affect the
operation of the device. The drain hole should be periodically cleaned
according to the following instructions:
• Remove the sprocket cover and chain.
• Remove the debris with a thin screwdriver or similar tool.
• Install the battery and start the device using the switch. The oil will
flow, removing any remaining impurities.
• Remove the battery. Refit the chain and close the sprocket
cover (fig. G1) .
CHANGING THE SPROCKET
A damaged or worn sprocket will damage the chain. Therefore, always
check the condition of the sprocket before replacing the chain (fig. H1) .
If the rack is worn, replace it with a new one together with the circlip (fig.
I1) .
STORAGE
Before storing the device for an extended period of time, please follow the
instructions below:
• Clean the device in accordance with the points above.
• Remove the head.
• After cleaning the device, lubricate it by running it without load.
• Put on the guide bar cover.
• Drain the oil reservoir.
PERIODIC MAINTENANCE
The table below shows the maintenance activities and the recommended
period of time to perform them.
Element / function
When / what how many?
Chainsaw
Control
Before use
Cleaning
After use
Inspection at an authorized
service point
Every year / before storage
Saw chain
Control
Before use
Sharpening
Before storage / in case of
emergency
Runner
Control
Before / after use
Disassembly
Before storing
Lubrication
Lubrication system check
Before use
Switch
Control
Before use
Switch lock
Control
Before use
Oil plug
Checking tightness
Before use
Nuts and bolts
Control
Weekly
TROUBLESHOOTING
Problem
Possible cause
Proposed solution
The saw does not start.
Incorrect battery
installation.
Install the battery according to
the instructions.
Battery problem (low
voltage).
Charge the battery and replace if
there are further problems.
Block.
Press the unlock button
The saw switches itself
off after a short time.
Low battery.
Charge the battery and replace if
there are further problems.
Chain not lubricated.
Empty oil reservoir.
Top up the oil.
Dirty guide.
Clean.
Lubrication system
obstruction
Clean.
The saw does not reach
its maximum speed.
Incorrect battery
installation.
Install the battery according to
the instructions.
Low battery.
Charge the battery and replace if
there are further problems.
Defective drive.
Repair at an authorized service
point.
Vibrations too strong
(switch off immediately!)
Loose chain or guide
bar.
Adjust the position of the guide
and the tension.
Device damage.
Repair at an authorized service
point.
OPERATING MANUAL - HEDGE SHEARS
Note: The following instructions are valid for the included hedge trimmer.
ADJUSTING THE POSITION OF THE SCISSORS
Press the head position button and turn it to the required angle. Release
the pressure on the button to lock the position. The angle can be adjusted
from -22.5 ° to 90 ° in 6 positions (fig. J1, K1) .
Note: After adjusting the angle, make sure that the head is in one of the 6
possible positions (clicking sound).
TRANSPORTING THE TOOL
When carrying the tool, remove the battery and put the scissors cover
on. To remove the cover, gently squeeze it then pull (fig. L1) .
PRUNING
While standing on a solid surface and assuming a stable position, set
yourself up so that the angle between the boom and the ground during
work does not exceed 60 °. While working, gently press the cut
twigs. Thicker branches should be cut in fragments
CLEANING THE CUTTER BAR
The cutting bar should be cleaned with a dry or damp, soapy and
squeezed cloth. After work, clean the strip from dust with a brush and
lubricate it (fig. M1) .
Note: do not use gasoline, alcohol or other chemicals for cleaning. It may
damage the device. Do not wash the skirting board under running water
or immerse it in water, as it may cause corrosion.
LUBRICATION
Before work or every hour during work, apply a low-density grease, eg in
a spray, to the cutterbar (fig. N1) .
STORAGE
Before storing the device for an extended period of time, please follow the
instructions below:
• Clean the device in accordance with the points above.
• Remove the head.
• Put the cutterbar cover on.
• Store the tool out of the reach of children, in a dry place and not
exposed to rain.
TROUBLESHOOTING
Problem
Possible cause
Proposed solution
The engine is not
running.
Battery not in place.
Install the battery according to the
instructions.
Battery voltage too
low.
Charge the battery and replace if there
are further problems.
Defective drive.
Repair at an authorized service point.
The cutters switch off
after a short time.
Battery voltage too
low.
Charge the battery and replace if there
are further problems.
Overheating.
Stop the machine and let it cool down.
Drive does not reach
maximum speed
Battery not installed
properly.
Install the battery according to the
instructions.
Battery voltage too
low.
Charge the battery and replace if there
are further problems.
Defective drive.
Repair at an authorized service point.
Blades do not move
(turn off
immediately!)
Wrong blade angle.
Make sure the head is properly installed.
Foreign bodies
between the blades.
Turn off the device. Use pliers to remove
debris.
Defective drive.
Repair at an authorized service point.
Vibrations too strong
(switch off
immediately!)
Blades damaged,
bent or worn.
Replace the blades.
Defective drive.
Repair at an authorized service point.
Motor and blades do
not stop (remove
battery immediately!)
Electricity failure.
Remove the battery. Repair at an
authorized service point.
ENVIRONMENTAL PROTECTION
Electrically powered products should not be disposed of with
household waste, but should be disposed of in appropriate
facilities. Information on disposal is provided by the dealer of the
product or local authorities. Waste electrical and electronic equipment
contains substances that are not neutral for the natural
environment. Non-recycled equipment is a potential threat to the
environment and human health..
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with its
registered office in Warsaw, ul. Pograniczna 2/4 (hereinafter: "Grupa Topex") informs that
all copyrights to the content of this manual (hereinafter: the "Manual"), including its text,
photos, diagrams, drawings, and its compositions belong exclusively to the Topex Group
and are subject to legal protection in accordance with the Act of February 4, 1994, on
copyright and related rights (i.e. Journal of Laws of 2006 No. 90 Item 631, as amended).
Copying, processing, publishing, modifying for commercial purposes the entire Manual
and its individual elements, without the consent of Grupa Topex expressed in writing, is
strictly prohibited and may result in civil and criminal liability.
DE
ORIGINAL (BETRIEBSANLEITUNG)
KETTENSÄGE UND AUSLEGERHECKENSCHERE
58G098
ACHTUNG WICHTIG: VOR VERWENDUNG DES
ELEKTROWERKZEUGS SORGFÄLTIG LESEN
DIESES HANDBUCH UND BEWAHREN SIE DIESES HANDBUCH
ZUM NACHSCHLAGEN AUF.
SPEZIELLE SICHERHEITSREGELN FÜR AUSLEGERSÄGEN
Bekijk gratis de handleiding van Graphite Energy+ 58G098, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Graphite |
| Model | Energy+ 58G098 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 23208 MB |
