Graphite 58GE111-AD handleiding
Handleiding
Je bekijkt pagina 8 van 55
8
table in the operating instructions. Charging incorrectly or at
temperatures outside the specified range can damage the battery
and increase the risk of fire.
BATTERY REPAIR:
ATTENTION! The battery is not included in the kit
• Damaged batteries must not be repaired. Repairs to the battery are
only permitted by the manufacturer or an authorised service centre.
• The used battery should be taken to a disposal centre for this type
of hazardous waste.
SAFETY INSTRUCTIONS FOR THE CHARGER
• The charger must not be exposed to moisture or water. The ingress
of water into the charger increases the risk of shock. The charger
may only be used indoors in dry rooms.
• Unplug the charger from the mains before carrying out any
maintenance or cleaning.
• Do not use the charger placed on a flammable surface (e.g. paper,
textiles) or in the vicinity of flammable substances. Due to the
temperature increase of the charger during the charging process,
there is a danger of fire.
• Check the condition of the charger, cable and plug each time before
use. If damage is found - do not use the charger. Do not attempt to
disassemble the charger. Refer all repairs to an authorised service
workshop. Improper installation of the charger may result in a risk of
electric shock or fire.
• Children and physically, emotionally or mentally challenged
persons, as well as other persons whose experience or knowledge
is insufficient to operate the charger with all safety precautions,
should not operate the charger without the supervision of a
responsible person. Otherwise there is a danger that the device will
be mishandled resulting in injury.
• When the charger is not in use, it should be disconnected from the
mains.
• All charging instructions must be followed, and the battery must not
be charged at a temperature outside the range specified in the rating
table in the operating instructions. Charging incorrectly or at
temperatures outside the specified range can damage the battery
and increase the risk of fire.
PICTOGRAMS AND WARNINGS
1.Read the operating instructions, observe the warnings and safety
conditions contained therein.
2.Wear safety goggles, ear protection and a dust mask.
3.Keep children away from the appliance.
4.Protect from rain.
5.Use , protected from water and moisture.
6.Recyclable.
7.Selective
collection.
8.Do not throw the cells into the fire.
9.Posing a risk to the aquatic environment.
10.Do not allow heat to exceed 45°C.
DESCRIPTION OF THE GRAPHIC ELEMENTS
The numbering below refers to the components of the device
shown on the graphic pages of this manual.
Fig.A
1.Screwing depth adjustment knob
2.Strip guide with screws
3.Feeder box assembly
4.Feeder
5.Plunger for selecting the length of the screws to be used
6.Limiter base
7.Tape with screws
8.Screwdriver bit (bit)
Fig.B
1.Screwdriver (not included)
2.Head with handle
3.Screwing depth adjustment
4.Direction of rotation switch
5.Switch
6.Work area illumination lamp
7.Continuous operation lock button
8.Handle
9.Handle for hanging the screwdriver on the belt
10.Rechargeable battery (not included)
Fig.C
1, 2, 3. Pulling the ring off the head
4.Installation of the screwdriver bit (bit)
5.Assembly of feeder box assembly with screwdriver
* There may be differences between the graphic and the actual
product
PREPARATION
The adaptor for the plasterboard screwdriver is a device that works with the
58GE111 battery-powered screwdriver. The adapter is designed for
screwing screws into plasterboard. The adapter proves to be particularly
useful for work involving the installation of plasterboard buildings and
walls, room adaptations, etc.
PREPARATION FOR WORK
ADAPTER ASSEMBLY
• Set the direction of rotation switch Fig. B12 to the centre position.
• Then pull the adjustment ring fig.B11 until it comes off the head
fig.C1-3
• Install the bit fig. A8 into the magnetic socket fig. C4
• To install the feeder box assembly fig.A3, push it firmly onto the
screwdriver head until it locks into place with a slight click fig.C5.
INSTALLATION OF TAPE WITH SCREWS
• To install the screw belt fig.A7, pass it through the screw guide
fig.A2. Then pass it through the feeder box until the first screw
reaches the ready position.
• To remove the screw strip fig.A7, push in the screw length setting
pin fig.A5 and pull the strip upwards.
ACTION
CRAFTING
• Move the rocker switch lever Fig.B4 to the screwdriving position.
• Always check the screw tip carefully for wear before starting. A worn
tip must be replaced, otherwise poor fixing may result.
• Always hold the tool perpendicular to the working surface. Holding
the tool at an angle can cause damage to the screws and wear on
the tip. It can also lead to poor fastening.
• Always hold the tool firmly against the screwing surface until the
screwing is completed. Failure to do so may result in insufficient
tightening of the screws.
• Do not apply oil or grease to the sliding surface of the feeder box.
EXTRACTION
• Remove the feeder box assembly fig.A3
• Move the reversing switch lever fig.B4 to the unscrew position and
use the tool as a screwdriver to unscrew.
BATTERY TYPES AND CAPACITIES
The unit is suitable for use with ENERGY+ batteries 58G001, 58G001-
1, 58G004, 58G004-1, 58G086, 58G086-1, 58GE152.
We recommend the use of the 4 Ah 58G004-1 battery
Battery type
58G001
58G001-1
58G004
58G004-1
58G086
58G086-1
58GE152
Battery
capacity
2 Ah
4 Ah
6 Ah
8 Ah
Working time
52 min
101 min
165 min
210 min
CHARGING THE BATTERY
Battery charging should be carried out in conditions where the ambient
temperature is 4ºC - 40ºC. A new battery, or one that has not been used
for a long period of time, will reach full power capability after approximately
3 - 5 charge and discharge cycles.
• Remove the battery from the device.
• Plug the charger into a mains socket (230 V AC).
Bekijk gratis de handleiding van Graphite 58GE111-AD, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Graphite |
| Model | 58GE111-AD |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 14175 MB |
