Handleiding
Je bekijkt pagina 19 van 56
19
Preparing the electrical connection
Requirement:Only after-sales service staff who have
been trained accordingly may carry out work on the
inside of the appliance or replace the power cord.
1. Observe the information about the electrical con-
nection.
An incorrect installation, an improper installation
or connection invalidates the warranty.
2. If a longer mains power cable is required, contact
the after-sales service. Connecting cables up to
2.20m are available.
3. On appliances without a preinstalled cable, insert
the power cable into the mains socket.
Opening the mains socket
▶
Use a screwdriver to lift the cover of the mains
outlet.
→Fig.
17
Preparing the mains socket
1. Undo the screw.
→Fig.
18
2. Use a screwdriver to lift the strain relief.
→Fig.
19
3. Loosen the strain relief.
→Fig.
20
Connecting the cable to the mains socket
1. For 3N, connect the cable to the mains socket in
accordance with the following figure.
→Fig.
21
2. For 2N, connect the cable to the mains socket in
accordance with the following figure.
→Fig.
22
3. For 1N, connect the cable to the mains socket in
accordance with the following figure.
→Fig.
23
4. For 2L/2N, connect the cable to the mains
socket in accordance with the following figure.
→Fig.
24
5. Note the colours of the cables.
– BN: Brown
– BU: Blue
– GN/YE: Yellow and green
– BK: Black
– GY: Grey
6. If required, install the enclosed copper bridges in
accordance with the connection diagram.
7. Connect the cables and then tighten the screws of
the mains socket.
8. For a 1N~ or 2L/2N connection in accordance
with the connection diagram, 1 corresponds to the
fan motor.
9. For a 2N~/3N~ connection, phase L1 (grey) cor-
responds to the fan motor.
Secure the cable in the mains socket
1. Use the strain relief to secure the power cable in
place.
2. Tighten the screw at the correct position.
‒ Do not use a cordless screwdriver.
→Fig.
25
3. To facilitate closing the mains socket, arrange the
cables in the central area of the mains socket.
4. Close the cover on the mains socket.
QR code: Electrical connection
This is where you will find the QR code for the video
for the electrical connection.
→Fig.
26
Instructions for the exhaust air pipe
The appliance manufacturer does not provide any
warranty for faults attributable to the pipeline.
¡ Use a short, straight exhaust air pipe with as large
a pipe diameter as possible.
¡ Long, rough exhaust air pipes, many pipe bends
or small pipe diameters reduce the suction power
and increase the fan noise.
¡ Use an exhaust air pipe that is made of non-com-
bustible material.
¡ To prevent condensate from returning, fit the ex-
haust pipe with a 1° gradient from the appliance.
Instructions for the air extraction mode
For air extraction mode, a one-way flap should be in-
stalled.
Notes
¡ If a one-way flap is not included with the appli-
ance, one can be ordered from a specialist re-
tailer.
¡ If the exhaust air is conveyed through the external
wall, a telescopic duct should be used.
Checking the units
1. Check whether the fitted unit is level and has suffi-
cient load-bearing capacity.
The maximum weight of the appliance is approx.
25kg.
The worktop into which you are fitting the appli-
ance must be able to withstand loads of approx.
60kg.
2. Ensure that the stability of the fitted unit is also
guaranteed following cut-out work.
3. Use suitable substructures to ensure the load-
bearing capacity and stability, particularly in the
case of thin worktops.
‒ Take the appliance weight, including additional
load, into consideration.
‒ Use heat-resistant and moisture-resistant rein-
forcement material.
4. Ensure that the fitted unit is heat-resistant up to
90°C.
5. Do not support any other appliances, e.g. ovens,
refrigerators, dishwashers or washing machines.
6. Only check that the appliance is level once it has
been installed in the installation opening.
7. You can freely select the clearance to a top cab-
inet. In doing so, take into consideration the ease
of use and ergonomics when using the plate.
Flush installation
With the flush installation, the appliance and worktop
are on one level. There is no unattractive stepping
between the appliance and the worktop.
You can install the appliance in the following
temperature-resistant and waterproof worktops:
¡ Stone worktops
¡ Plastic worktops, e.g. Corian®
¡ Solid wood worktops
Installation in compressed-wood worktops is not pos-
sible.
Preparing the units
Requirement:The fitted units are heat-resistant up to
90°C.
Bekijk gratis de handleiding van Gaggenau CV492105M, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Gaggenau |
| Model | CV492105M |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 8546 MB |
