Furman PL-PROC handleiding
Handleiding
Je bekijkt pagina 6 van 24
6
PL-PRO C OWNER’S MANUAL
ULTRA-LOW RESISTANCE MAGNETIC POWER SWITCH / CIRCUIT BREAKER:
Furman’s Classic Series 20 amp capacity power switch is specically designed to stand up to the enormous high in-rush current
demands of many power ampliers. Addionally, Furman magnec circuit breakers are not sensive to temperature, and will not
raise the AC impedance as do many, less costly thermal breaker. If the 20 amp RMS current capacity of the PL-PRO C is exceeded, the
spring tensioned-switch will immediately switch to the o posion. You will need to switch the toggle back to the on posion once the
problem is corrected (typically by eliminang one component, or unl the RMS current does not exceed 20 amps or 2400 was).
EXTREME VOLTAGE SHUTDOWN (EVS) INDICATOR:
The Extreme Voltage LED Indicator is normally o. It is located to the le of the power switch, though during normal use it will NOT be lit.
The Extreme Voltage indicator monitors a hazard common in the entertainment, remote broadcast, and AV contractor industries:
wiring faults. For example: accidental connecon to 208VAC where 120VAC is expected, or an open series neutral from a 208 to
240VAC electrical service. The Furman EVS circuit senses voltages that are so high that operaon would be impossible and shuts the
power down before damage can occur.
Upon inially applying power to the PL-PRO C, the Extreme Voltage indicator will illuminate to a bright red if the input voltage is above
the extreme voltage cuto. When this occurs, power will not be applied to the PL-PRO C’s outlets. If the unit has been operang with
an acceptable input voltage and subsequently that voltage exceeds 140V, it will shut o power to the outlets and the Extreme Voltage
LED will light.
NOTE: If the mains power is above the high cuto voltage and has caused the EVS circuit to remove power from the PL-PRO C’s
outlets, it cannot restore power without the operator manually turning the unit o, then on again. Avoid turning the unit back on
without rst checking the source of the problem and changing the AC source (if necessary).
PROTECTION OK INDICATOR:
Although the Furman SMP circuit assures virtually maintenance-free protecon from transient voltage spikes and surges, nature has a
way of occasionally creang electrical forces that are beyond the capabilies of ANY surge suppression device to absorb without some
degree of damage (such as a direct lightning hit in an outdoor applicaon). In the rare instance that this occurs, the green “Protecon
OK” LED indicator (located to the right of the retractable light tubes), will not be illuminated. If this happens, some level of protecon
from voltage surges will remain, but the PL-PRO C’s clamping voltage rang will be compromised and the unit must be returned to
Furman for service.
NOTE: Furman’s Classic Series power condioners do not compensate for high or low AC line voltage. If you frequently move your
rack to dierent locaons, derive power from generators, use very long extension cords, travel internaonally, or are in an area prone
to brownouts, you may benet from the use of one of Furman’s AC Voltage Regulators.
MULTI-SEGMENT LED VOLT METER:
This three-color, 20-LED bar-graph is an accurate, self-checking AC voltmeter that connually measures input AC voltage. The meter
reads from 90 to 128 volts in 2 volt increments. The opmal range voltages are indicated in green, with moderate and extremely high
or low voltages in yellow and red, respecvely. The voltmeter provides three special ashing paerns to indicate abnormal condions:
1. If only the single le-most (beneath the 90V mark) LED ashes, the input voltage is marginally low.
2. If all of the LED’s on the voltmeter ash, the input voltage is marginally high. Power to the PL-PRO C’s outlets will remain unless
the incoming voltage rises above the Extreme Voltage Shutdown (EVS) cuto voltage (140 volts).
3. (If none of the LED’s on the voltmeter are lit, and the Extreme Voltages LED indicator is illuminated, then the PL-PRO C has shut
down power to its outlets because the input voltage is in a range considered extreme (in excess of 140 volts).
USB CHARGER:
The Furman PL-PRO C’s USB charger provides an easy way to recharge many popular electronic accessories as well as cellular
communicaon devices by simply plugging the re-charge cord into the front panel socket. Please note that as there are currently
many standards for USB, some devices may not be compable with our charger.
TRANSFORMER PLUG (WALL WART) SECURING LOOPS:
Your 20 amp Furman Classic Pro Series condioner features rear panel AC outlets that are widely spaced for plug transformers (wall
warts). Addionally, these may be secured for transport with hook and loop straps (included). Each outlet has threaded screw holes
on either side to accommodate the hook and loop straps.
Bekijk gratis de handleiding van Furman PL-PROC, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Furman |
| Model | PL-PROC |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2961 MB |
Caratteristiche Prodotto
| Kleur van het product | Zwart |
| Gewicht | 5443 g |
| Breedte | 482.6 mm |
| Diepte | 266.7 mm |
| Hoogte | 44.45 mm |
