Friedrich ZoneAire Select PZH07K3SB handleiding

Airco

Friedrich

37 pagina's

PDF beschikbaar

Handleiding

A. IMPORTANT SAFETY AND GENERAL INFORMATION

Automatic Room Freeze Protection–automatically keeps the temperature in the room from getting too cold, where water pipes might

freeze. If the unit is conﬁgured for the freeze protection feature to be active (which is the default condition), then whenever power is supplied to

the unit, and the unit senses the temperature is below 40°F, the fan motor and electric heater are turned on, and will warm the room to 50°F.If

Freeze protection is not required, change the conﬁguration switch to turn the feature off (see section J.3 Dip switches on unit conﬁguration).

Automatic defrost protection –When the outdoor temperature gets too cold (approx. 28°F) and the unit can no longer effectively

heat with the compressor, the unit will automatically switch to electric heating. The unit will then heat with electric heat until the outside

temperature rises enough (approx.40°F), so the compressor can be used again.

Automatic Quick Warmup (for heat pump models only)-If the room temperature falls to 5°F below the set point temperature, the

reverse cycle heat is shut off and the electric strip heat is turned on for one cycle, until heating is satisﬁed.

LED Indicator’s and Buttons The touch pad has buttons for POWER, UP, DOWN, COOL, HEAT, CONSTANT FAN, HIGH, LOW and AUTO.

It also has LEDs that correspond to the mode, fan speed and setpoint operation, to indicate the unit’s status. The LEDs above the CONSTANT

FAN, COOL, and HEAT mode buttons indicate what operating mode is active. The LEDs above the LOW, AUTO, and HIGH buttons indicate the fan

speed that is selected. The LED above the power button is the unit On/Off status LED. If the unit is in ON mode, the LED will be blue. If the unit is

OFF, the LED will go out.

Conﬁgure Fan to Optimize Selected Application Unit can be optimized to selected application by conﬁguring the fan to run in

continuous mode or cycle on and off with the compressor and electric heater. In cycle mode, fan will continue to run for a while after

compressor or electric heater stops in order blow off any residual heat or cool left on coil.

Unit Conﬁguration There are many different conﬁguration possibilities, through both dip switches and the digital keypad, that allow

you to conﬁgure the unit for your exact application. See section J.3 on unit conﬁguration for more details. Following are the conﬁguration

selections that have not previously been mentioned:

Temperature Display The unit can display in either °For °C

Indoor Temperature Sensor Biasing Optimize the room temperature sensor reading to your exact application (one for cooling and an

other for heating).

Emergency Heat (for Heat Pump Only) Disable the compressor during heating mode operation (heat only with Electric Heat).

Display Setpoint or Room Temperature The unit can be conﬁgured to display the room temperature or setpoint only, during heating

and cooling modes. See section J.3 on unit conﬁguration for more details.

Limit the Setpoint Range The unit can be conﬁgured to limit the controlling setpoint range. The display will always show the complete

setpoint range, but the controlling setpoint will be limited to the conﬁgured minimum and maximum setpoint selected. See section J.3 on unit

conﬁguration for more details.

Energy Management (Sometimes known as Front Desk Control) an input is provided so that the unit can be manually disabled from a

different location. If the unit detects 24vac on this input, it will automatically turn itself off. If no voltage is detected on the input, the unit will run

normally.

Wall Thermostat Control A wired wall thermostat can be connected to the unit. If it is, the unit must be conﬁgured to disable the

keypad. See section J.3 on wired inputs and unit conﬁguration for more details.

Bekijk gratis de handleiding van Friedrich ZoneAire Select PZH07K3SB, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.