Fischer FIS SB 390 S HWK big handleiding
Handleiding
Je bekijkt pagina 14 van 20
14
Installation instruction
see ICC-ES Evaluation Report
No. 3572 at www.icc-es.org
See ICC-ES
Evaluation Report
at www.icc-es.org
ESR-1990
fischer adhesive anchoring system FIS SB
fischer FIS SB is an epoxy adhesive anchoring system for fastenings in normal weight concrete.
Important: Before use, read and review the installation instructions and the SDS (safety data sheet).
Do not use expired adhesive.
A Preparing the cartridge
1. Remove the cap by turning and pulling it off.
2. Screw on the static mixer (FIS MR Plus/FIS UMR) tightley and lock it in place (turn to the right).
The spiral element mixer in the static mixer must be clearly visible.
Never use without the static mixer !
3. Place the cartridge in the dispenser. Press approx. 10 cm of material out until the resin mortar
comes out evenly grey in colour. Mortar which is not grey colour will not cure and must be
disposed off.
The temperature of the concrete must be at least 5 °F (–15 °C) and at most 104 °F (40 °C) (see
Table VII). – The temperature of the cartridge must be at least = 41 °F (5 °C).
After finishing work, leave the static mixer attached to the cartridge.
Important: If the processing time is exceeded, use a new static mixer and if necessary remove
encrusted material in the cartridge mouth.
B Installation
Important: Installation instructions – follow the pictograms 1–7 for the sequence of operating
and refer to Tables I–VI for setting details. The construction drawings must be adhered. For any
applications not covered by this document, or by any problems with installation contact fischer.
1. Drill hole with a hammer drill set. Observe the correct hole diameter and depth according to
Tables I–VI.
2.1/2.2a/2.2b/2.3. Standing water in bore holes must be completely removed by blowing out
before cleaning the bore hole. The drill hole must blown out twice with compressed air (oil-free
≥ 87 psi (6 bar)), brushed two times (minimal by hand) starting from the bottom of the hole and
then again blown out twice with compressed air (oil-free ≥ 87psi (6bar)). For drill holes d
0
< 18
mm it is allowed to use hand pump. The diameters of the brushes are given in Table I. Clean
dirty brushes. Check brushes for wear with brush gauge (brush Ø ≥ drill hole Ø). If required use
brush extension.
3. Fill approx. ⅔ of the hole with mortar starting from the bottom of the hole. For drill hole
depth > 150 mm use an extention tube. Observe processing time.
4. Anchoring element must be straight and free of oil and other contaminants. Mark the anchor with
correct embedment depth. Press the anchoring element down to the bottom of the hole, turning it
slightly while so doing. After insert the anchoring element, excess mortar must emerge from the
mouth of the hole.
5. For overhead installations use wedges to support the anchor. For overhead installations, drill hole
diameter > 30 mm, or drill hole depth > 250 mm use an injection adapter.
6. Do not disturb the anchoring element until cure time has elapsed. Do not apply load or installation
torque moment to the anchor until the prescribed curing times are elapsed. The allowable working
time and the minimum curing time are given in Table VII.
7. The installation torque moments are given in Table II.
Table VII. Processing and curing times.
Temperature range Adhesive Temperature
Working time /
processing time
Curing time
[ °C ] [ °F ] [ °C ] [ °F ] [ min ] [ h ]
– 15 to – 10 + 5 to + 14 ≥ +5 ≥ +41 60 36
– 10 to – 5 + 14 to + 23 ≥ +5 ≥ +41 30 24
– 5 to ± 0 + 23 to + 32 ≥ +5 ≥ +41 20 8
± 0 to + 5 + 32 to + 41 ≥ +5 ≥ +41 13 4
+ 5 to + 10 + 41 to + 50 ≥ +5 ≥ +41 9 2
+ 10 to + 20 + 50 to + 68 ≥ +10 ≥ +50 5 1
+ 20 to + 30 + 68 to + 86 ≥ +20 ≥ +68 4 3/4
+ 30 to + 40 + 86 to + 104 ≥ +25 ≥ +77 2 1/2
Store mortar in
a cool dry place.
+ 5 — + 25 °C
+ 41 — + 77 °F
Bekijk gratis de handleiding van Fischer FIS SB 390 S HWK big, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Fischer |
| Model | FIS SB 390 S HWK big |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4118 MB |
