Fischer FIS EM Plus 390 S handleiding
Handleiding
Je bekijkt pagina 12 van 21
2322
Installation instructionInstallation instruction
see ICC-ES Evaluation Report
No. 1990 at www.icc-es.org
EN
fischer adhesive anchoring system FIS EM Plus
fischer FIS EM Plus is an epoxy adhesive anchoring system for fastenings in
normal weight concrete.
Important: Before use, read and review the installation instructions and the SDS
(safety data sheet). Do not use expired adhesive. Minimal concrete temperature
– 5 °C (23 °F).
Drilling and cleaning the hole (hammer drilling with standard drill bit)
>6 bar
2x
>6 bar
2x
2x
1
4a
2a
4b
2b 3
1 Drill the hole. Nominal drill hole diameter d
0
and drill hole depth h
0
see Tables
II, III, IV or VI, VII, VIII respectively.
2a Cleaning of the drill hole (not applicable for underwater installation): Blow out
the drill hole twice, with oil free compressed air (p ≥ 6 bar / 87 psi).
2b For underwater installation only: Flush the drill hole with clean water until it
flows clear.
3 Brush the drill hole at least twice, brush type see Table I or V respectively.
For drill hole diameter ≥ 30 mm / 1 1/2 inch use a power drill. For deep holes
use an extension.
4a Cleaning of the drill hole (not applicable for underwater installation): Blow out
the drill hole twice, with oil free compressed air (p ≥ 6 bar / 87 psi).
4b For underwater installation only: Flush the drill hole with clean water until it
flows clear.
→ Go to step 6.
Drilling and cleaning the hole (hammer drilling with hollow drill bit)
1 2
1 Check a suitable hollow drill for correct operation of the dust extraction.
2 Use a suitable dust extraction system, e. g. fischer FVC 35 M or a comparable
dust extraction system with at least equivalent performance data (volume
flow at the hose end ≥ 36 l/s / 1.27 cfs). Drill the hole with hollow drill bit. The
dust extraction system has to extract the drill dust nonstop during the drilling
process and must be adjusted to maximum power. Nominal drill hole diameter
d
0
and drill hole depth h
0
see Tables II, III, IV or VI, VII, VIII respectively.
→ Go to step 6.
Drilling and cleaning the hole (wet drilling with diamond drill)
2x
>6 bar
2x
>6 bar
2x
1a
4
1b
5
2 3
1a Drill the hole. Drill hole diameter d
0
and nominal drill hole depth h
0
see Tables
II, III, IV or VI, VII, VIII respectively.
1b Break the drill core and remove it.
2 Flush the drill hole with clean water until it flows clear.
3 Blow out the drill hole at least twice, using oil free compressed air
(p ≥ 6 bar / 87 psi).
4 Brush the drill hole at least twice using a power drill, brush type see
Table I or V respectively.
5 Blow out the drill hole at least twice, using oil free compressed air
(p ≥ 6 bar / 87 psi).
Preparing the cartridge
6 7
6 Remove the sealing cap. Screw on the static mixer (the spiral in the static
mixer must be clearly visible). Place the cartridge into the dispenser.
7 Extrude approximately 10 cm / 4 inch of material out until the resin is evenly
grey in colour. Do not inject mortar that is not uniformly grey.
See ICC-ES
Evaluation Report
at www.icc-es.org
Bekijk gratis de handleiding van Fischer FIS EM Plus 390 S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Fischer |
| Model | FIS EM Plus 390 S |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2364 MB |
