Festool HLC 82 EB handleiding
Handleiding
Je bekijkt pagina 18 van 103
9.2 Putting the planer down
WARNING
Risk of injury
The planing head continues to run for a few seconds
after it has been switched off.
► Use the power tool only with fully functional support
foot[1-12].
► Wait until the planing head comes to a standstill.
The power tool has a support foot[1-12] at the end of the
planer foot to safely place the planer down. When the
power tool is lifted up, the support foot automatically
extends over the foot of the planer so that the spiral
blade does not touch the surface when the power tool is
placed down on a flat surface.
9.3 Chamfering[6]
To chamfer workpiece edges, the front planer foot has
three 90° V-shaped grooves[6-1]. These V-shaped
grooves are3mm, 2mm or 1mm deep, so that when the
chip thickness is setto0, the edge is broken by
approximately3mm, 2mm or 1mm.
10 Service and maintenance
WARNING
Risk of injury, electric shock
► Always remove the battery pack from the power tool
before performing any maintenance or service
work.
► Any maintenance and repair work that requires the
motor housing to be opened must only be carried
out by an authorised service workshop.
Customer service and repairs must only be carried out
by the manufacturer or service workshops. You must only
use original Festool spare parts.
Further information: www.festool.co.uk/service
To ensure constant air circulation, always keep the
cooling air openings in the motor housing clean and free
of blockages.
Keep the contacts on the power tool, charger and battery
pack clean.
Cleaning the chip ejector
► Remove the battery pack.
► Remove the chip channel, see section8.5.
► Empty the chip channel and remove any blockages.
► Loosen jammed chips from the ejector opening[5-2]
and clean the power tool with a resin solvent if
necessary.
► Connect the extractor, see section8.5.
► Vacuum the chip ejector opening.
11 Accessories
WARNING
Risk of injury
► Remove the battery pack from the power tool before
performing any work on the power tool.
You can find the PO numbers for accessories and tools
under
www.festool.co.uk.
Some of the accessories listed below are included in the
scope of delivery.
11.1 Fitting the rebate depth stop[7]
The rebate depth stop[7-2] can be adjusted anywhere
between 0 and23mm. Read the set rebate depth from
the marking[7-1].
11.2 Fitting the parallel side fence[8]
To plane along an edge, first loosen the clamp[8-1], then
use the fence to adjust the planing width between 0
and82mm.
11.3 Fitting the chamfer adaptor[9]
The chamfer adaptor[9-1] guides the power tool through
a groove at an angle of approximately 45° during
chamfering.
0
Set the minimum chamfer width [10A].
2
Set the maximum chamfer width [10B].
12 Environment
Do not dispose of electrical devices, used
batteries and battery packs in the household
waste. Recycle devices, accessories and
packaging. Observe applicable national regulations.
Before disposing of used batteries, battery packs and
lamps, separate them from the electrical device without
destroying them. This means they can be recycled
efficiently.
In accordance with the European Directive on waste
electrical and electronic equipment and implementation
in national law, used electrical devices must be collected
separately and handed in for environmentally friendly
recycling.
Information on the collection points can be viewed at
www.festool.com/environment.
Information on critical materials: www.festool.co.uk/
reach
13 General information
Imported into the UK by
FestoolUKLtd
1AngloSaxonWay
BuryStEdmunds
IP309XH
GreatBritain
13.1 Licence information
Licence information on any open source licences used in
the product can be found in the Festoolapp* at
Information> Power tool open source licenses.
*Not available in all countries.
13.2 Information on data privacy
The power tool contains a chip which automatically
stores machine and operating data. The data saved
cannot be traced back directly to an individual.
The data can be read in a contactless manner using
special devices and shall only be used by Festool for fault
diagnosis, repair and warranty processing and for quality
improvement or enhancement of the power tool. The data
English
18
Bekijk gratis de handleiding van Festool HLC 82 EB, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Festool |
| Model | HLC 82 EB |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 15398 MB |
