Fantini Cosmi ASPIRLIGHT BP handleiding
Handleiding
Je bekijkt pagina 14 van 24
ASPIRLIGHT BP
14
RDV-RF
7.2 RFT-remote controllers
The Advance unit has a RFT-receiver on board. The
remote controller must be paired to the Advance unit.
It is possible to connect more remote controllers to one
Advance unit (maximum 20 remote controllers).
Pairing:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ ), or ( + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Tip!
Pairing the remote controller to the Advance unit in the
direct vacinity of the unit makes the job easier to do!
Disconnect already connected remote controllers:
In the situation of wrongly paired remote controllers
or reinstalling installation parts, first disconnect
the remote controller(s) before you start the pairing
procedure:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ + + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Conditions for good operation:
- Max length receiver/transmitter 25 metre indoor.
- No metal shield in ceiling or wall.
Buttons function:
Low speed
Middle speed
Boost speed
Timer, 10 minutes/step (up to 30 minutes)
ITHO
|
advance
19
211.0107 Advance 226-0047 A4 Installer ENGELS.indd 19 14-02-11 15:39
Bassa Velocità
Media Velocità
Alta Velocità
Timer, intervalli di 10 minuti (fino a 30 minuti)
7. COLLEGAMENTO A RADIO FREQUENZA
L’ASPIRLIGHT BP può essere anche comandato da telecomando a radio frequenza modello RDV-RF.
L'interruttore RDV-RF può essere utilizzato per selezionare una delle tre modalità di ventilazione
(capacità): bassa, media e alta.
La modalità bassa viene utilizzata di notte, la modalità media durante il giorno quando ci sono persone in casa, e
la modalità alta durante la cottura, doccia o il bagno.
Gli interruttori RDV-RF sono spesso collocati in locali umidi (cucina, bagno, ecc).
Possono essere utilizzati fino a 20 interruttori per azionare l’ASPIRLIGHT BP.
Il comando è dotato di Timer.
Quando il pulsante timer viene premuto l'unità di ventilazione passa in modalità alta per un tempo predeterminato.
Dopo che è trascorso il tempo del timer l’unità passa automaticamente in modalità bassa.
L'impostazione del tempo dipende dal numero di volte che viene premuto il pulsante timer consecutivamente:
- Premere il pulsante del timer per 1 volta per impostare l'unità di ventilazione in modalità alta per 10 minuti.
- Premere il pulsante del timer per 2 volte per impostare l'unità di ventilazione in modalità alta per 20 minuti.
- Premere il pulsante del timer per 3 volte per impostare l'unità di ventilazione in modalità alta per 30 minuti.
Se l'interruttore di funzionamento viene utilizzato scegliendo la modalità bassa, media o alta mentre il timer è in
funzione, il timer viene disattivato e l'unità di ventilazione funziona nella modalità scelta.
Il funzionamento in radiofrequenza non richiede ulteriori cablaggi.
7.1 ABBINAMENTO DEL TELECOMANDO ALL’UNITÀ
Disconnettere l'alimentazione principale per almeno 15 secondi
Ricollegare l'apparecchio all'alimentazione elettrica
Entro 120 secondi premere contemporaneamente i tasti
7.2 RFT-remote controllers
The Advance unit has a RFT-receiver on board. The
remote controller must be paired to the Advance unit.
It is possible to connect more remote controllers to one
Advance unit (maximum 20 remote controllers).
Pairing:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ ), or ( + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Tip!
Pairing the remote controller to the Advance unit in the
direct vacinity of the unit makes the job easier to do!
Disconnect already connected remote controllers:
In the situation of wrongly paired remote controllers
or reinstalling installation parts, first disconnect
the remote controller(s) before you start the pairing
procedure:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ + + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Conditions for good operation:
- Max length receiver/transmitter 25 metre indoor.
- No metal shield in ceiling or wall.
Buttons function:
Low speed
Middle speed
Boost speed
Timer, 10 minutes/step (up to 30 minutes)
ITHO
|
advance
19
211.0107 Advance 226-0047 A4 Installer ENGELS.indd 19 14-02-11 15:39
+
7.2 RFT-remote controllers
The Advance unit has a RFT-receiver on board. The
remote controller must be paired to the Advance unit.
It is possible to connect more remote controllers to one
Advance unit (maximum 20 remote controllers).
Pairing:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ ), or ( + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Tip!
Pairing the remote controller to the Advance unit in the
direct vacinity of the unit makes the job easier to do!
Disconnect already connected remote controllers:
In the situation of wrongly paired remote controllers
or reinstalling installation parts, first disconnect
the remote controller(s) before you start the pairing
procedure:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ + + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Conditions for good operation:
- Max length receiver/transmitter 25 metre indoor.
- No metal shield in ceiling or wall.
Buttons function:
Low speed
Middle speed
Boost speed
Timer, 10 minutes/step (up to 30 minutes)
ITHO
|
advance
19
211.0107 Advance 226-0047 A4 Installer ENGELS.indd 19 14-02-11 15:39
oppure
7.2 RFT-remote controllers
The Advance unit has a RFT-receiver on board. The
remote controller must be paired to the Advance unit.
It is possible to connect more remote controllers to one
Advance unit (maximum 20 remote controllers).
Pairing:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ ), or ( + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Tip!
Pairing the remote controller to the Advance unit in the
direct vacinity of the unit makes the job easier to do!
Disconnect already connected remote controllers:
In the situation of wrongly paired remote controllers
or reinstalling installation parts, first disconnect
the remote controller(s) before you start the pairing
procedure:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ + + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Conditions for good operation:
- Max length receiver/transmitter 25 metre indoor.
- No metal shield in ceiling or wall.
Buttons function:
Low speed
Middle speed
Boost speed
Timer, 10 minutes/step (up to 30 minutes)
ITHO
|
advance
19
211.0107 Advance 226-0047 A4 Installer ENGELS.indd 19 14-02-11 15:39
+
7.2 RFT-remote controllers
The Advance unit has a RFT-receiver on board. The
remote controller must be paired to the Advance unit.
It is possible to connect more remote controllers to one
Advance unit (maximum 20 remote controllers).
Pairing:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ ), or ( + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Tip!
Pairing the remote controller to the Advance unit in the
direct vacinity of the unit makes the job easier to do!
Disconnect already connected remote controllers:
In the situation of wrongly paired remote controllers
or reinstalling installation parts, first disconnect
the remote controller(s) before you start the pairing
procedure:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ + + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Conditions for good operation:
- Max length receiver/transmitter 25 metre indoor.
- No metal shield in ceiling or wall.
Buttons function:
Low speed
Middle speed
Boost speed
Timer, 10 minutes/step (up to 30 minutes)
ITHO
|
advance
19
211.0107 Advance 226-0047 A4 Installer ENGELS.indd 19 14-02-11 15:39
In caso di errato abbinamento del telecomando all'unità di ventilazione o di
sostituzione di scheda elettronica, è necessario effettuare questa procedura per
resettare il precedente abbinamento.
Disconnettere l'alimentazione principale per almeno 15 secondi
Ricollegare l'apparecchio all'alimentazione elettrica.
Entro 120 secondi premere contemporaneamente i tasti
7.2 RFT-remote controllers
The Advance unit has a RFT-receiver on board. The
remote controller must be paired to the Advance unit.
It is possible to connect more remote controllers to one
Advance unit (maximum 20 remote controllers).
Pairing:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ ), or ( + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Tip!
Pairing the remote controller to the Advance unit in the
direct vacinity of the unit makes the job easier to do!
Disconnect already connected remote controllers:
In the situation of wrongly paired remote controllers
or reinstalling installation parts, first disconnect
the remote controller(s) before you start the pairing
procedure:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ + + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Conditions for good operation:
- Max length receiver/transmitter 25 metre indoor.
- No metal shield in ceiling or wall.
Buttons function:
Low speed
Middle speed
Boost speed
Timer, 10 minutes/step (up to 30 minutes)
ITHO
|
advance
19
211.0107 Advance 226-0047 A4 Installer ENGELS.indd 19 14-02-11 15:39
+
7.2 RFT-remote controllers
The Advance unit has a RFT-receiver on board. The
remote controller must be paired to the Advance unit.
It is possible to connect more remote controllers to one
Advance unit (maximum 20 remote controllers).
Pairing:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ ), or ( + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Tip!
Pairing the remote controller to the Advance unit in the
direct vacinity of the unit makes the job easier to do!
Disconnect already connected remote controllers:
In the situation of wrongly paired remote controllers
or reinstalling installation parts, first disconnect
the remote controller(s) before you start the pairing
procedure:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ + + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Conditions for good operation:
- Max length receiver/transmitter 25 metre indoor.
- No metal shield in ceiling or wall.
Buttons function:
Low speed
Middle speed
Boost speed
Timer, 10 minutes/step (up to 30 minutes)
ITHO
|
advance
19
211.0107 Advance 226-0047 A4 Installer ENGELS.indd 19 14-02-11 15:39
+
7.2 RFT-remote controllers
The Advance unit has a RFT-receiver on board. The
remote controller must be paired to the Advance unit.
It is possible to connect more remote controllers to one
Advance unit (maximum 20 remote controllers).
Pairing:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ ), or ( + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Tip!
Pairing the remote controller to the Advance unit in the
direct vacinity of the unit makes the job easier to do!
Disconnect already connected remote controllers:
In the situation of wrongly paired remote controllers
or reinstalling installation parts, first disconnect
the remote controller(s) before you start the pairing
procedure:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ + + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Conditions for good operation:
- Max length receiver/transmitter 25 metre indoor.
- No metal shield in ceiling or wall.
Buttons function:
Low speed
Middle speed
Boost speed
Timer, 10 minutes/step (up to 30 minutes)
ITHO
|
advance
19
211.0107 Advance 226-0047 A4 Installer ENGELS.indd 19 14-02-11 15:39
+
7.2 RFT-remote controllers
The Advance unit has a RFT-receiver on board. The
remote controller must be paired to the Advance unit.
It is possible to connect more remote controllers to one
Advance unit (maximum 20 remote controllers).
Pairing:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ ), or ( + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Tip!
Pairing the remote controller to the Advance unit in the
direct vacinity of the unit makes the job easier to do!
Disconnect already connected remote controllers:
In the situation of wrongly paired remote controllers
or reinstalling installation parts, first disconnect
the remote controller(s) before you start the pairing
procedure:
- Disconnect the electric power cord from the mains
supply for at least 15 seconds.
- Push Button (
+ + + ) together for at
least 5 seconds within 120 seconds after plugging in
the electric power cord of the Advance unit.
Conditions for good operation:
- Max length receiver/transmitter 25 metre indoor.
- No metal shield in ceiling or wall.
Buttons function:
Low speed
Middle speed
Boost speed
Timer, 10 minutes/step (up to 30 minutes)
ITHO
|
advance
19
211.0107 Advance 226-0047 A4 Installer ENGELS.indd 19 14-02-11 15:39
Bekijk gratis de handleiding van Fantini Cosmi ASPIRLIGHT BP, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Fantini Cosmi |
| Model | ASPIRLIGHT BP |
| Categorie | Ventilator |
| Taal | Nederlands |
| Grootte | 2343 MB |
