Handleiding
Je bekijkt pagina 7 van 184
7
4. CONTROLS
On initial start-up the board recognises the mains frequency.
Recognition is signalled on the display by the fact that led G ashes and the panel shuts down.
Wait 10s. to allow the control board to perform calibration, before accessing the commands.
Button Function Led
A
The button only works when the door is open. -
Press Briey = Turns the Lights On/Off at maximum intensity. Fixed LED button A.
Press and hold for 2 Seconds = Turns the Courtesy Lights On/Off. Fixed LED button A.
B
Only works with the Door Open.
Press briey = Activates/Deactivates Delay mode, causing automatic shutdown
of the Motor and the Lighting system from any speed with a 30’ delay. It is disabled
by pressing the same button again, turning the motor off or closing the door.
Warning! This mode does not work if INTENSIVE mode has been activated rst.
LED Button B+ Button for the set Speed are lit.
Works both with the Door Closed and Open.
Press and hold for 2 Seconds = With the lter alarm triggered the Filter Alarm
is Reset, all leds ashing 3 times. These indications are only visible when the
motor is turned off.
Fixed LED button:
Indicates the need to wash the metal grease lters.
The alarm is triggered after the Hood has been in
operation for 100 working hours.
Flashing LED button:
Indicates the need to change the activated charcoal
lters, and also to wash the metal grease lters.
The alarm is triggered after the Hood has been in
operation for 200 working hours.
C
Only works with the Door Open.
Press briey = Activates speed four.
Fixed LED button C+G.
Only works with the Door Open.
Press and hold for 2 seconds = Enables/Disables the Intensive speed. This
speed is timed to run for 6 minutes. At the end of this time the system will return
to the speed set previously.
It is disabled by pressing the same button again, turning the motor off or closing
the door.
Flashing LED button C.
Fixed LED button G.
D
Only works with the Door Open.
Activates speed three.
Fixed LED button D+G.
E
Only works with the Door Open.
Activates/Deactivates speed two.
Fixed LED button E+G.
Works both with Door Closed and Open with Motor + Lights = Off.
Press and hold for 4 Seconds = Enables/disables the Keyboard lock.
All the LED buttons ash twice. During the Lock the
LED buttons light up in sequence.
F
Only works with the Door Open.
Press briey = Activates/Deactivates speed one.
Fixed LED button F+G.
Door Open or Closed
Press and hold for 2 Seconds = Enables/Disables the Activated Charcoal Filter
Alarm with the Motor turned off and no Filter Alarm triggered.
LED button B ashes twice = Activated Charcoal
lter Alarm Activated.
LED button B ashes once = Activated Charcoal
lter Alarm Deactivated.
G
Door Open
Press briey = Turns the Motor off.
LED button goes out.
Door Open or Closed
Press and hold for 2 Seconds with Motor and Lights Off = Enables/Disables the
Remote control.
LED button G + F ashes twice = Remote control
Enabled.
LED button G + F ashes once = Remote control
Disabled.
H
Door Open
Press briey = Closes the Door + Lights and Motor Off
Door Closed
Press briey = Opens the Door + Lights and Motor On.
Warning: If the Door remains partially open for any reason, press the Button to
complete the opening or closing cycle.
-
Bekijk gratis de handleiding van Faber Fabula Plus 60, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Faber |
| Model | Fabula Plus 60 |
| Categorie | Afzuigkap |
| Taal | Nederlands |
| Grootte | 18345 MB |
