Extron RCP 401 handleiding
Handleiding
Je bekijkt pagina 2 van 6
2
RCP 401 EU and RCP 401 MK • Setup Guide
Front Panel Lockout (Executive Mode)
When front panel lockout is on, all the buttons on the RCP 401 are disabled. To toggle between enabling or disabling front panel lockout,
press and hold the Pause and Mark buttons simultaneously for three seconds.
As front panel lockout is enabled, all buttons and the red activity LED (see igure1,
A
on page 1) blink three times. As front panel
lockout is disabled, all the buttons and the green activity LED (see igure1,
A
) blink three times. If a button is pressed while front
panel lockout is enabled, all buttons blink three times.
RCP 401 Rear Panel Features
The back panel features of the RCP 401 EU and RCP 401 MK are
identical (see gure 2).
A
USB connector — Connect the RCP 401 EU/MK to the rear
panel of the the SMP using the provided 6 foot (1.8 meter) USB-C
to USB-C cable. This connection provides power and control to
the RCP. To increase the distance up to 300 feet (100 m), use an
Extron UCS 900 Series extender (see www.extron.com).
To power the unit by connecting it to the SMP, use the
provided cable to connect to the rear panel of the SMP.
B
Cable anchor — Use a zip tie to secure the USB cable to this
anchor.
C
Power inlet — Optionally, the RCP 401 EU/MK can be powered
with a 12 VDC, 1.0 A power supply.
To power the unit with a power supply, connect the power
supply to this input. Ensure the polarity of the wires is correct
(
gure 3,
1
) and the wires are stripped correctly (
2
).
NOTE: We recommend powering up the RCP using the USB-C
connection.
B
A
C
Figure 2. RCP 401 Rear Panel
Power Receptacle
DC Power Cor
d
SECTION A–A
Ridges
Smooth
Power Supply
Output Cord
AA
3/16"
(5 mm) Max.
1
1
1
2
2
2
POWER
1.0A MAX
12V
Ground
all Devices
RidgedSmooth
– Return
+12 VDC input
Figure 3. Connecting Power to the RCP 401
ATTENTION:
• Always use a power supply provided by or specified by Extron. Use of an unauthorized power supply voids all regulatory
compliance certification and may cause damage to the supply and the end product.
• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron. L’utilisation d’une source d’alimentation non
autorisée annule toute certification de conformité réglementaire, et peut endommager la source d’alimentation et l’unité.
• If not provided with a power supply, this product is intended to be supplied by a UL Listed power source marked “Class 2” or
“LPS” and rated output 12 VDC, minimum 1.0 A.
• Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté par une source d’alimentation certifiée UL de
classe 2 ou LPS, avec une tension nominale 12 Vcc, 1,0 A minimum.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.
• Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une utilisation dans les espaces d’aération ou dans les
cavités murales.
• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA 70,
article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently fixed to building
structure or similar structure.
• Cette installation doit toujours être conforme aux dispositions applicables du Code américain de l’électricité (National
Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de l’électricité, partie 1, section 16. La source d’alimentation
ne devra pas être fixée de façon permanente à la structure de bâtiment ou à d’autres structures similaires.
2
3
Power inlet
Bekijk gratis de handleiding van Extron RCP 401, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Extron |
| Model | RCP 401 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1447 MB |
