Extron IPCP Pro 360 handleiding
Handleiding
Je bekijkt pagina 31 van 72
IPCP Pro Series • Hardware Features and Installation
23
Power Connections
NOTE: The IPCP Pro 250, IPCP Pro 255, IPCP Pro 350, and IPCP Pro 360 are suitable for use in an
environmental air space in accordance with section 300.22.C of the National Electrical Code, and
sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, part 1, C22.1.
A
Power input connector (external power supply) — Connect the IPCP to the included 12 VDC
power supply (part number 28-071-57LF or 28-327-57LF ) via this port (see figure 16, figure 17, and
figure 18,
A
on page 20 through page 22), then connect the external power supply to a 100 to 240 VAC
power source.
POWER
12V
x.xA MAX
POWER
12V
1A MAX
12V
1A MAX
POWER
AV LAN
R
R
Ground all devices.
– Return
+12 VDC input
Ridged
Smooth
External 12 VDC
Power Supply
To
AC
power
Front Panel,
Rack Mounted
Models
Power Input, External Power Supply
• Front panel LED ( ) blinks during
boot-up and remains lit when the
IPCP is powered and operational.
• Connect to
included 12 VDC
power supply.
NOTE:
Check the
polarity of the
power supply
before connecting
it to the IPCP.
RidgedSmooth
Tie Wrap
3/16"
(5 mm)
Max.
Front/
Bottom
Panel,
DIN Rail
Models
Rear
Panel,
Rack
Mounted
Models
Front Panel,
DIN Rail
Models
Figure 19. Connecting an External Power Supply
ATTENTION:
• Always use a power supply supplied or specified by Extron. Use of an unauthorized power supply
voids all regulatory compliance certification and may cause damage to the supply and the unit.
• Utilisez toujours une source d’alimentation fournie par Extron ou recommandée.
L’utilisation d’une source d’alimentation non autorisée annule toute certification de conformité
réglementaire, et peut endommager la source d’alimentation et l’unité.
• If not provided with a power supply, this product is intended to be supplied by a UL Listed power
source marked “Class 2” or “LPS” and rated output 12 VDC, minimum 1.0 A, 50° C.
• Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté par une source
d’alimentation certifiée UL de classe 2 ou LPS, avec une tension nominale 12 Vcc, 1 A minimum,
50° C.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall
cavities.
• Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une utilisation dans les
espaces d’aération ou dans les cavités murales.
• The installation must always be in accordance with the applicable provisions of National Electrical
Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16. The power
supply shall not be permanently fixed to building structure or similar structure.
• Cette installation doit toujours être conforme aux dispositions applicables du Code américain de
l’électricité (National Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de l’électricité,
partie 1, section 16. La source d’alimentation ne devra pas être fixée de façon permanente à la
structure de bâtiment ou à d’autres structures similaires.
Rev. G, 01.15.18:
Changed power supply from
isometric to orthographic per
Randy Drumm.
Rev. G, 08/20/18:
Updated the French
translation of the
2nd sentence.
Rev. M, 10/23/23: Per
Homi, added “50° C”
because UL requested
“Use UL Listed
external power supply
with rated output
12Vdc, min. 1.0A, NEC
Class 2, or LPS output,
50 Deg C “
Rev. G, 01/15/18:
Updated the French
translation with new text
from 05/24/17.
Bekijk gratis de handleiding van Extron IPCP Pro 360, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Extron |
| Model | IPCP Pro 360 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 11958 MB |
