Extron IN2004 handleiding
Handleiding
Je bekijkt pagina 4 van 6
4
Audio Wiring
Wire the audio input and output connectors as shown below right. Use the supplied tie wrap to strap the audio cable to the
extended tail of the connector.
ATTENTION:
• For unbalanced outputs, do not connect
wires to the “-” poles.
• Pour les sorties asymétriques, ne
connectez pas de câbles aux pôles
« - » .
NOTE: The length of exposed wires is
important. The ideal length is 3/16 inch
(5 mm).
Front Panel Features
DTP3 IN2004 DI/DO
CONFIG
SIGNAL STATUS
1
3
2
4
INPUT 1
INPUT 2
INPUT 3
INPUT 4
HDCP IN
HDCP OUT1A
HDCP OUT1B
HDCP OUT1C
MENU
HOLD FOR 1080p/4K
ENTER
A
CB D E F
Figure 2. Front Panel Features — All Models
A
USB configuration port — Connect a host device to this USB-C port for device configuration via PCS, control, file transfer
(user logos, audio files, and so on), and firmware updates.
NOTE: The CONFIG port supports TCP/IP connections with a xed IP address of 203.0.113.22.
B
Input selection buttons and LEDs (1-4) — Press one of these buttons to select an input. Each button has a green LED that
lights when the input is selected.
C
SIGNAL (input) LEDs — The green LED for each input lights when an active video signal is detected, regardless of which
input is currently selected.
D
STATUS LEDs — These green LEDs light to indicate the state of their corresponding settings:
• HDCP IN — Lights if the currently selected input video signal is encrypted.
• HDCP OUT 1A , 1B, and 1C — Light if the current output video signal is encrypted. These LEDs blink if the output sync is
muted. HDCP OUT 1C is on only the DO and DI/DO models.
• AUTO SW — Lights if the unit is in an auto-switch mode. This LED is on only the IN2004 standard model.
E
MENU and ENTER buttons — Press these buttons to access and navigate the on-screen display menu system.
F
Navigation buttons — Use these Right, Left, Up, and Down arrow buttons as follows:
• Press these buttons to navigate through the on-screen (OSD) menu system or change settings.
• Press and hold the Down arrow button for 5 seconds while the OSD is not in use to switch the output rate between 1080p
@ 60 Hz and 4K @ 60 Hz. Continued pressing of the Down arrow for an additional 5 seconds changes the output rate
back to the previous one (see the table below). This can be useful for troubleshooting if the output display shows no video.
Current Resolution Switches To
Rate other than 4K @ 60 Hz or 1080p @ 60 Hz 1080p @ 60 Hz
1080p @ 60 Hz 4K @ 60 Hz
4K @ 60 Hz 1080p @ 60 Hz
NOTE: This feature is not available when the unit is in front panel lock mode or when the OSD is in use.
When the down arrow has been pressed for the required duration of time, triggering an output resolution change,
the front panel LED columns (SIGNAL and STATUS) blink twice all together.
12
Balanced Audio Output
Tip
Ring
Tip
Ring
Sleeves
Unbalanced Audio Output
Tip
No Ground Here
No Ground Here
Tip
Sleeves
Unbalanced Audio InputBalanced Audio Input
Tip
Ring
Tip
Ring
Sleeves
Tip
Sleeve
Sleeve
Tip
Do not tin the wire
s!
12
12
12
A
USB CONFIG port
B
Input buttons and LEDs
C
SIGNAL LEDs
D
STATUS LEDs
E
MENU and ENTER buttons
F
Navigation buttons
2
Bekijk gratis de handleiding van Extron IN2004, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Extron |
| Model | IN2004 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1212 MB |
