Extron FOXBOX Rx HDMI handleiding
Handleiding
Je bekijkt pagina 27 van 51
FOXBOX Tx/Rx HDMI • Remote Control 19
Symbol Definitions for Transmitter SIS Commands
]
= CR/LF (carriage return/line feed)
}
= Carriage return (no line feed)
| = Pipe (can be used interchangeably with the
}
character)
• = Space (hard) character
E
= Escape key (hex 1B)
W = Can be used interchangeably with the
E
character
X! = EDID hex switch position 00 = User captured EDID 08 = 1360 x 768
01 = RS-232 control 09 = 1366 x 768
02 = 800 x 600 10 = 1400 x 1050
03 = 1024 x 768 11 = 1440 x 900
04 = 720p* 12 = 1600 x 1200
05 = 1280 x 768 13 = 1680 x 1050
06 = 1280 x 800 14 = 1080p*
07 = 1280 x 1024 15 = 1920 x 1200
* 720p and 1080p also include a block for embedded audio; all other
positions are video only
X@ = Refresh rate 1 = 50 Hz 2 = 60 Hz
X# = EDID See the table on page 21.
X$ = Native resolution Resolution and rate in an easily-viewed format, such as “800x600@60Hz“.
X% = EDID record 128 or 256 bytes
X^ = Input Audio Format 0 = follow switch 2 = force analog audio
1 = force digital audio 3 = Auto (digital if present, else analog)
X& = Audio gain adjustment range 00 to 10
X* = Audio level adjustment range –18 to +10 (in 1.0 dB steps)
X( = Audio attenuation adjustment range 00 to 18
X1) = Switch position and enable or disable status 0 = off (down) or disable 1 = on (up) or enable
X1! = HDCP authorized device 0 = off 1 = on
X1@ = Link and input status 0 = link or input not detected 1 = link or input detected
X1# = Internal temperature nnnF•nnC
X1$ = Transmission mode SM = singlemode MM = multimode
X1% = Firmware version v.vv
X1& = Frequency n.nn
Unit-initiated Messages
When a local event, such as an equipment power-up, occurs, the unit responds by sending
a message to the host. The unit-initiated messages are listed below:
(c) Copyright 20nn, Extron Electronics FOXBOX Tx HDMI, Vx.xx, 60-1174-xx
]]
- or -
(c) Copyright 20nn, Extron Electronics FOXBOX Rx HDMI, Vx.xx, 60-1174-xx
]]
The connected unit issues the appropriate copyright message (above) when it first powers
on. Vx.xx is the firmware version number; 60-1174-xx is the part number of the connected
unit.
Reconfig
]
The unit sends the Reconfig message whenever the video input signal to the transmitter is
changed.
1Lnk
X1@
•2Lnk
X1@
•Vid
X1@
•Aud
X1@
]
The unit sends the status message whenever a change in the fiber link and video
connection occurs.
EmbedAud
X1)
]
The unit sends the Embedded audio message whenever a change in the position of the
receiver rear panel HDMI Audio switch occurs.
Bekijk gratis de handleiding van Extron FOXBOX Rx HDMI, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Extron |
| Model | FOXBOX Rx HDMI |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7241 MB |
