Extron FOX3 SR 301 handleiding
Handleiding
Je bekijkt pagina 14 van 58
FOX3SR 301 and FOX3SR311 Scaling Receivers • Installation 6
B
Power LED (see figure2 on page5) — The lit LED indicates power is applied.
C
Audio Return— Connect a balanced or unbalanced audio input to this 5-pole captive
screw port for return to the transmitter (see Analog Audio Connectors on page9
to wire this connector).
D
Audio output — This 5-pole captive screw port outputs the transmitted, unamplified,
line level analog audio (see Analog Audio Connectors to wire this connector).
NOTE: If embedded digital audio is present on the HDMI output, this analog audio
connector outputs audio unless embedded audio is in multi-ch format.
E
USB Device ports — (see USB HID and USB 2.0 Connectors on page11)
• USB HID — Connect USB type A to B cables between this USB type B port
and the USB port of a device. The USB HID ports are used only for a mouse or
keyboard.
• USB 2.0 (FOX3SR301 only) — Connect USB type A to B cables between this
USB type B port and the USB port of a device. The USB 2.0 ports are used for
thumb drives, cameras, keyboards, a mouse, CAC reader, and such devices.
F
HDMI output — Connect a video display to this HDMI output port with a maximum
resolution of 4096x2160 @ 60 Hz, 8-bit, 4:4:4 chroma sampling (see HDMI
Connectors on page8 to use the included Extron Lock-It Lacing Bracket).
G
Remote RS-232/3D Sync port —
• Remote RS-232 port — For serial control of the receiver, connect a host device,
such as a computer or touch panel control, via the three left poles (Tx, Rx, and G)
of this 5-pole captive screw port (see RS-232 and IR Connectors on page10
to wire this connector).
• 3D Sync port — For stereoscopic 3D sync, such as external IR emitter for glasses,
connect a PC to the two right poles of the REMOTE RS-232/3D Sync 5-pole
captive screw port on the receiver (see RS-232 and IR Connectors to wire this
connector).
H
Control RS-232/IR port — Connect a serial RS-232 signal, a modulated or
unmodulated IR signal, or both to this 3.5 mm, 5-pole captive screw port for
bidirectional RS-232 and IR communication (see RS-232 and IR Connectors to wire
the connector).
NOTE: If only one fiber optic cable is connected (see figure3 on page7),
RS-232 or IR reports from the controlled device cannot be received. To receive
responses from the controlled device, two fiber optic cables must be connected.
I
LAN Ethernet port — If desired, connect the receiver to an Ethernet LAN or WAN
via this RJ-45 port. Ethernet control allows the operator to control the receiver via SIS
commands, the PCS configuration software, or embedded webpage from a remote
location (see TP Cable Termination and Recommendations on page10 to wire
the connector).
• Link (green) LED — Indicates that the unit is properly connected to an Ethernet
LAN. This LED should light steadily.
• Act (yellow) LED — Indicates transmission of data packets on the RJ-45
connector. This LED should blink as the unit communicates.
Bekijk gratis de handleiding van Extron FOX3 SR 301, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Extron |
| Model | FOX3 SR 301 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10927 MB |
