Envertec EVT2000 handleiding
Handleiding
Je bekijkt pagina 10 van 22
15 16
5. Microinverter System Installation
Installing Envertech microinverter system involves several key steps. Each
step listed here is elaborated on the following pages.
Step 1. Verify voltage
Step 2. Mount microinverters onto the rack
Step 3. Ground the system
Step 4. Install a Wi-Fi antenna
Step 5. Fasten AC cables
Step 6. Connect to the grid
Step 7. Connect PV modules to microinverters
Step 8. Switch on the PV system
Step 9. Monitoring device (EnverBridge) installation
Step 10. Wi-Fi configuration
Step 11. Monitoring
Step 1. Verify the voltage range
Verify the grid and PV panel voltages are within the microinverter voltage
range.
Step 2. Mount microinverters
Mark out the estimated center of PV modules on the rack to mount the
microinverter.
Mount all microinverters under modules to avoid rain and sun. Make sure
you can see the LED light.
Note: Please strictly follow the relevant content of Maximum Units Per
Branch (12AWG Cable) in the datasheet for installation.
Step 3. Ground the system
Microinverters and modules must be connected to the ground. Fix the screws
to the microinverter installation hole. Make sure that the grounding screw
thread is firmly connected the bracket.
Step 4. Install the Wi-Fi antenna
Rotate the antenna clockwise until it is firmly secured to the microinverter.
Step 5. Fasten AC and DC cables
Fasten AC cables, DC cables and grounding cables to the rack with cable ties.
For R version microinverter, insert end cap on unused side.
1
2
www.envertec.com
Envertech (Shanghai) Corporation LTD.
Model: EVT800PV Microinverter
Operating Range (Vdc):
16V~60V
MPPT Voltage Range (Vdc):
22V~50V
Max. DC Input (Vdc):
60V
Max. Input Continuous Current (A):
14Ax2
Max. Input Short-Circuit Current (A):
25A
Ingress Protection (IP):
IP67
Power (Max. Continuous) (W):
800W
Temperature (℃):
-40℃ to +65℃
Normal Voltage (Vac):
220/230V
Current (Max. Continuous) (A):
3.63A
Normal Frequency (Hz):
50Hz/60Hz
Power Factor Range:
+/-0.90
Overvoltage Category: OVC III (AC Main)
OVC II ( PV)
Protective Class: Class I
User Identification Number
User Identification Number
1
www.envertec.com
Envertech(Shanghai)Corporation LTD.
Address:Building C, No. 8 Shiyuan Road,Songjiang District,Shanghai
Operating Range (Vdc):
MPPT Voltage Range (Vdc):
Max. DC Input (Vdc):
Max. Input Continuous Current (A):
Max. Input Short-Circuit Current (A):
Ingress Protection (IP):
Temperature(℃):Power (Max. Continuous) (W):
16V~60V
22V~50V
60V
20Ax4
25Ax4
IP67
-40℃ to +65℃2000W
Normal Voltage (Vac):
Current (Max. Continuous) (A):
Normal Frequency (Hz):
Power Factor Range:
Protective Class:
Overvoltage Category:
L/N/PE,220V/230V
9.09A
50Hz/60Hz
+/-0.90
Class I
OVC III(AC Main),OVC II(PV)
VFR 2019,CEI 0-21:2019,2016/631 EU - (NC RfG)
IEC/EN 62109-1/-2,IEC/EN 61000-3-2/-3,IEC/EN 61000-6-1/-2/-3/-4
IEC/EN 55014-1/-2,EN 50549-1:2019,VDE-AR-N 4105:2018,TOR 2019
OVE R25:2020,NA/EEA-NE7-CH:2022,C10/11:2019,UTE C15-712-1:2013
2
3
4
Only qualified personnel may connect the Envertech
microinverter to the utility grid after receiving prior approval
from the electrical utility company.
You must install the microinverter system under connection
neither to the grid nor to the PV modules (or if not
disconnected, the modules should be shaded).
Installation could only be implemented when the system is
disconnected from the grid, and the solar panel has been
covered or disconnected.
Bekijk gratis de handleiding van Envertec EVT2000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Envertec |
| Model | EVT2000 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6025 MB |
