EMOS D1AM01 handleiding
Handleiding
Je bekijkt pagina 1 van 24
1
zdroj: m:\INDESIGN\_Skupinove navody Vanoce\manual_8_connect_START_UNIT_adaptery.indd 105 × 148 mm
GB | LED Connecting System
The „Connecting System“ is a system of light chains that can be extended to a maximum of 800 LED.
Use only in conjunction with a 30 V DC transformer and light chains from the EMOS system.
„Connecting System“
The light sources are not replaceable.
Do not connect to power supply if the conductor insulation is damaged.
Do not connect the light chain to power supply if it is still in packaging.
Do not interconnect parts of this light chain with parts of light chains made by a dierent manufac-
turer. I.e. the light chain must not be connected to light chains, transformers or cabling connection
systems of other brands.
Connection is done using only the supplied connectors. All open ends must be sealed before use. I.e.
before using the device, check that the end plug around the socket connector is closed.
In case the connecting cable or the light chain has to be replaced due to damage, use only cables
approved by the manufacturer.
Should the light source rupture or become damaged, do not use the light chain or leave it connected
to the power supply. Instead, dispose of it in a safe, environment-friendly way.
Not suitable for year-long outdoor use.
WARNING – THIS LIGHT CHAIN MUST NOT BE USED WITHOUT THE APPROPRIATE GASKETS!
WARNING – RISK OF INJURY BY ELECTRICAL CURRENT! DO NOT USE WITH MISSING OR DAMAGED
LIGHT SOURCES!
The product is designed for decorative lighting.
The product is not a toy; do not put it in the hands of children!
Timer (T):
The light chain has a built-in timer on the body of the transformer (adapter). After the rst connec-
tion, the chain will be constantly lit. After the second connection (a green light will light up), the
timer will be set to 6 hours. Afterwards, it turns o automatically and will remain o for 18 hours.
The timer will operate automatically in these intervals (6 hours on/18 hours o) until turned o by
making a third contact.
Example:
The chain will turn on on 1 December at 18 o‘clock. It will remain lit until midnight, then turns o
automatically. On 2 December, it will turn on automatically at 18 o‘clock and turn o again at midnight.
That means that the chain only has to be turned on once, and it will automatically keep lighting in
this fashion until you turn it o.
Changing the timer settings:
If you wish to change the time when the chain automatically turns on and o (e.g. 19 o‘clock until
1 o‘clock), all you need to do is turn o the chain at the desired time (if it is turned on) and then
turn it on again.
Note: The timer may deviate by a few minutes per month. If you want to adjust the turn-on timer
back to the original time, set the timer again.
EMOS spol. s r.o. declares that the LED Connecting System is in compliance with the essential
requirements and other relevant provisions of Directive. The device can be freely operated in the EU.
The Declaration of Conformity can be found at http://www.emos.eu/download.
Do not dispose with domestic waste. Use special collection points for sorted waste. Contact
local authorities for information about collection points. If the electronic devices would be
disposed on landll, dangerous substances may reach groundwater and subsequently food
chain, where it could aect human health.
Bekijk gratis de handleiding van EMOS D1AM01, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | EMOS |
| Model | D1AM01 |
| Categorie | Verlichting |
| Taal | Nederlands |
| Grootte | 2081 MB |
Caratteristiche Prodotto
| Kleur van het product | Zwart |
| Timer | Ja |
| Snoerlengte | 10 m |
| Materiaal behuizing | Polyvinyl chloride (PVC) |
| Aantal lampen | 100 gloeilamp(en) |
