Handleiding
Je bekijkt pagina 11 van 229
potentially result in carbon monoxide poisoning. After
installation of a range hood or other cooking fume
extractor, the operation of flued gas appliances should be
tested by a competent person to ensure that back flow of
combustion gases does not occur.
ELECTRICAL CONNECTION SAFETY
● Disconnect the product from the mains. ● Installation
must be carried out by professionally qualified personnel
with knowledge of the regulations in force for installation
and safety. ● The manufacturer denies all liability to
persons, animals or property if the guidelines provided in
this chapter are not followed. ● By law, the product must
be earthed. ● The power cable must be long enough to
allow the product, built into the cabinet, to be connected to
the mains. ● The power cable must be long enough to
allow removal of the hob from the worktop. ● Do not use
power strips or extension cords. ● Check that the voltage
on the rating plate on the bottom of the product
corresponds to that of the domestic environment where it
will be installed. ● The earth cable must be 2cm longer
than the other cables. ● The temperature must not reach
50°C above room temperature anywhere along the cable.
● The product is designed to be permanently connected to
the mains; for this reason, make the connection to the
mains via an omnipolar switch in accordance with the
installation rules, which ensures complete disconnection
from the mains in overvoltage category III conditions, and
which is easily accessible after maintenance. ● Once
installation is complete, the electrical components must no
longer be accessible by the user. ● Please note! Do not
connect the product to the mains until the installation is
complete. ● Before connecting the product to the mains:
check the rating plate (on the bottom of the product) to
ensure that the voltage and power correspond to the mains
supply and that the power socket is suitable. If in doubt,
consult a qualified electrician.
● If the product is not equipped with a power cable, use
one with a minimum conductor section of 2.5 mm
2
for
power up to 5500 Watt; while for higher powers it must be 4
mm
2
).
● Please note! The interconnection cable must be
replaced by the authorised customer service representative
or by a person with similar qualifications.
● Please note! Before reconnecting the circuit to the
mains power supply and making sure that it is working
correctly, always check that the power cable is correctly
installed.
INSTALLATION SAFETY
● The electrical and mechanical installation must be
performed by qualified personnel.
● Before starting the installation: After unpacking the
product, check that it has not been damaged during
transport and in the case of problems, contact your dealer
or Customer Service, before proceeding with the
installation; Check that the purchased product is the right
size for the installation location; Check for accessories
inside the packaging (placed there for ease of transport,
such as bags containing screws, the warranty certificate,
etc.). Remove and keep them safe; Also check that there is
a power socket near the installation area
● Preparing the cabinet for installation:
• Create the cut-outs in the cabinet before inserting the hob
and carefully remove shavings or sawdust.
The minimum distance between the hob and the wall must
be at least 50mm from the front, at least 50mm from the
sides and at least 500mm from the upper wall units.
NB: when designing the space, the kitchen manufacturer's
instructions must be followed.
• Important: use a single component adhesive sealant (S)
that can withstand high temperatures up to 250°; before
installation, the surfaces that need to be glued must be
thoroughly cleaned, removing all substances that may
compromise adhesion (e.g. release agents, preservatives,
grease, oils, powders, old adhesive residue, etc.); the
adhesive must be evenly spread along the entire perimeter
of the frame; after gluing, leave the adhesive to dry for
about 24 hours.
● Please note! Failure to install screws and fasteners in
accordance with these instructions may result in electrical
hazards.
● Note: for correct installation of the product, it is
recommended to tape the pipes using an adhesive with the
following characteristics: soft elastic PVC film, with acrylic-
based adhesive; complies with DIN EN 60454 regulations;
flame retardant; excellent resistance against wear; resistant
to temperature fluctuations; can be used at low
temperatures.
END-OF-LIFE DISPOSAL
This device is marked in compliance with the
European Directive 2012/19/EC - UK SI 2013
No.3113, Waste Electrical and Electronic Equip-
ment (WEEE).
Make sure that this product is disposed of correctly. The
user helps prevent potential negative consequences for the
environment and for health. The symbol on the product or
accompanying documentation indicates that this product
should not be treated as household waste but should be
handed over at a suitable collection point for the recycling
of electrical and electronic equipment. Dispose of it in
accordance with local regulations for waste disposal. For
further information about the treatment, recovery and
recycling of this product, please contact your local
authority, the collection service for household waste or the
shop from where the product was purchased.
REGULATIONS
This appliance, intended to come into contact with
foodstuffs, complies with Regulation (EC) no.1935/2004
and has been designed, manufactured and placed on the
market in accordance with the safety requirements of the
“Low Voltage” Directive 2014/35/EU and with the protection
requirements of the “EMC” Directive 2014/30/EU.
11
Bekijk gratis de handleiding van Elica Primis 804 Plus, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Elica |
| Model | Primis 804 Plus |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 31522 MB |
