Electro Harmonix 8-Step Program handleiding
Handleiding
Je bekijkt pagina 22 van 25
22
28
DEPTH
Smoothly controls the DEPTH
parameter over its entire range
0…100=0% to
100%
101…127 amplify
step values that are
set below step slider
maximum
29
TAP DIVIDE
Controls the TAP DIVIDE setting 0=off or 1/4 note
1=dotted 8th
2=1/4 note triplet
3=8th note
4=8th note triplet
5=16th note
6=32nd note
30
EXP
ression
MODE
Controls the EXPression MODE
setting
0=off
1=RATE
2=DEPTH
3=GLIDE
4=SEQ LENGTH
5=EXT. CLOCK
31
PLAY MODE
Controls the PLAY MODE setting.
Whenever this setting changes, the
digit display flashes the new mode.
0=LOOP
1=1-SHOT
2=STEP-THRU
33
Encoder MODE
Directly sets the Encoder MODE 0=GLide
1=DIRection
2=Seq Length
3=DEPTH
4=Preset
34
PLAY FSW
Engages PLAY function. In Step-
Thru mode both 0 and 127
advance the sequence.
0=stop
127=start
35
RESET FSW
RESET FSW press 127=RESET FSW
press
36
TAP FSW
TAP FSW press 127=TAP FSW press
37
TAP DIVIDE
BUTTON
TAP DIVIDE Button press 127=TAP DIVIDE
press
39
EXP. MODE
BUTTON
EXP. MODE Button press 127=EXP. MODE
press
40
ENCODER MODE
BUTTON
ENCODER MODE Button press 127=MODE press
41
Sequencer Step
When the sequencer is stopped or
if PLAY MODE is set to Step-Thru,
this CC forces the sequencer to
jump to a step immediately. If the
sequencer is running, this CC is
ignored
1…8 directly
chooses the
sequencer step
117
Save Preset
Save current 8-STEP settings to
preset number specified in data
field of this CC message. If the
data value is above 99, the CC
message is ignored.
0…99= immediately
save to preset
number equal to
value of CC
118
Load Preset
Load or cue preset. Preset number
is specified in the data field of this
CC message. If the data value is
above 99, the 8-STEP unloads the
current preset.
0…99= load preset
number equal to
value of CC.
100…127= unload
preset
19
3.
The preset has been saved; you can release the SELECT knob.
SAVING PRESETS WITH MIDI
1.
You can save the 8-STEP’s current setting by sending a MIDI message using CC
117.
2.
The MIDI controller must be set to the 8-STEP’s current MIDI Channel.
3.
The data value that is sent along with MIDI CC 117 will be the location that the
preset is saved in. The 8-STEP overwrites the old preset that was at this location.
For example, if you want to store your settings to preset number 3, send MIDI CC
117 with a data value equal to 3.
4.
The 8-STEP can save up to 100 presets via MIDI (using values 0 through 99), any
data value above 99 will be ignored.
5.
When saving presets with MIDI, be careful because the preset is saved
immediately upon receiving the proper MIDI message.
FACTORY RESTORE
The following procedure erases all presets and configuration settings on the 8-STEP and sets
them to their factory defaults.
1.
Apply power to the 8-STEP PROGRAM.
2.
While the 8-STEP is performing its start-up LED animation (which is approximately
4 seconds), press and hold both the TAP and PLAY FSWs. You must hold both
FSWs for at least 1 second and through the end of the animation.
3.
If you held both the TAP and PLAY FSWs down properly, you will see an
F
on the
digit display, plus all LEDs will be off except for BEAT, PLAY and STEP 1.
4.
Once you see the F on the digit display, release both FSWs.
5.
The 8-STEP is now in a mode where it is waiting for its next instruction; you should
see the
F
digit and the BEAT and PLAY LEDs blink at a slow rate.
6.
At this point, to start the Factory Restore function, press and release the PLAY
FSW. While the Factory Restore is working, the
F
digit will blink at a medium rate.
The Factory Restore takes approximately 2 seconds. Once you press the PLAY
FSW, there is no turning back on the Factory Restore.
7.
If you want to exit instead of performing the Factory Restore, press and release
the TAP FSW while the
F
digit is blinking at a slow rate. The 8-STEP immediately
loads your last configuration settings.
- MIDI -
The 8-STEP PROGRAM can be controlled by MIDI Control Change (CC) and Program Change
(PC) messages as well as sync to MIDI Clock. Every parameter on the 8-STEP’s top panel
can be controlled via MIDI CC as well as saving and loading all 100 presets. All buttons and
footswitches can also be controlled by MIDI PC messages. MIDI PC messages can directly
load all 100 presets.
Bekijk gratis de handleiding van Electro Harmonix 8-Step Program, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Electro Harmonix |
| Model | 8-Step Program |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2757 MB |