Elation STAGE SETTER-8 handleiding
Handleiding
Je bekijkt pagina 9 van 12
Front Panel - Controls and Functions (Cont.)
3. Mode Button:
This button is used to change the unit’s operating mode. There are
three different operating modes: 2x8, 8x8, and 1x16. The unit’s current
operating mode will indicated by a LED. that corresponds to the oper-
ating mode icons. Mode operations are explained on page 15.
4. Program Button:
This button is used to activate the unit’s program mode. You may create
up to eight of your own programs. These programs are then stored on
the Pattern Buttons (17). See programing on page 17.
When the Program Button is depressed the program LED will begin
to glow, this indicates Program Mode has been activated. Once Pro
-
gram Mode is activated you may begin to program chase patterns or
static scenes into the eight user Pattern Buttons (17). For programming
details, see the programming section beginning on page 17.
5. X Crossfader:
This slider controls the overall intensity of the Scene X channel faders
(2).
The X (5) and Y (6) faders allow crossfading between Scenes X (2) and
Scene Y (11) The X Crossfader is at its maximum intensity while in the
full up position.
In 1x16 mode, the X Crossfader controls the intensities of channels
1-16
6. Y Crossfader:
This slider controls the overall intensity of the Scene Y channel faders
(11).
The X (5) and Y (6) faders allow crossfading between Scenes X (2) and
Scene Y (11) The Y Crossfader is at its maximum intensity while in the
full down position.
In 1x16 mode, the Y Crossfader controls the scene Fade Time.
The offset configuration of the X (5) and Y (6) crossfaders allows easy
Elation Professional® - www.elationlighting.com - Stage Setter 8™ Instruction Manual Page 9
Stage Setter 8™ Controls and Functions
Masters Scenes (Cont.):
2. Lower all Scene X sliders to minimum.
3. Raise Scene X slider 1 and 6 to maximum.
4. Raise Scene X slider 7 to 50%.
5. Tap the Program Button. The Program LED should be lit.
6. Tap Bump Button 5.
Flash Scenes:
Flash Scenes that only operates in 1x16 mode. When in the 1x16
mode, the Bump Buttons (10) can be programmed as Flash Scenes.
These are scenes that can be created by any of the 16 channels. Once
a Flash Scene is created this scene may be activate by pressing on the
Bump Button it was assigned to. To create a Flash Scene:
First, use the sliders in the Scene X (2) and Scene Y (11) section to
create a scene. After you have set your scene, tap the Program Button
to enter the program mode. Once Program mode has been activated,
tap the Bump Button that corresponds to a Scene Y slider that will
be used to store the scene. The scene will now be stored as a Master
Scene into the Scene Y slider and will be ready for immediate use.
Example:
In this example we will program Bump Button 8, allowing channels 3, 7,
14 and 15 to be at full, channel 1, 5, 10 and 16 at 50% output and the
remaining channel fully off.
1. Move all Scene X and Scene Y sliders to fully down.
2. Move Scene X sliders 3 and 7 to fully up.
3. Move Scene Y sliders 14 and 15 to fully up.
4. Move Scene X sliders 1 and 5 to 50%.
5. Move Scene Y sliders 10 and 16 to 50%.
6. Tap the Program Button causing its LED to light.
7. Tap Bump Button 8.
Stage Setter 8™ General Operation
Elation Professional® - www.elationlighting.com - Stage Setter 8™ Instruction Manual Page 16
Bekijk gratis de handleiding van Elation STAGE SETTER-8, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Elation |
| Model | STAGE SETTER-8 |
| Categorie | Verlichting |
| Taal | Nederlands |
| Grootte | 1749 MB |
