Ekko ES60E handleiding
Handleiding
Je bekijkt pagina 53 van 65
Maintenance
51
12. Working at the platform controls, press
the lift function select button. Lower the
platform to the stowed position.
⊙ Result: The diagnostic LCD displays "18",
the alarm sounds and the lift function operates.
The machine is functioning properly.
¤ Result: The diagnostic LCD does not
display "18". The alarm does not sound and
the lift function does not operate. Replace the
down limit switch.
13. Press and hold the drive/steer function
enable switch on the control handle.
Attempt to drive and steer the machine.
⊙ Result: The diagnostic LCD displays "18 ".
The alarm sounds, and the drive and steer
function do not operate. The machine is
function properly.
¤ Result: The diagnostic LCD does not
display "18". The alarm does not sound, and
the steer and drive functions operate. Replace
the down limit switch.
14. Press the platform up button. Raise the
platform approximately 0.3 m.
⊙Result: The diagnostic LCD displays "18".
The alarm sounds. The machine is functioning
properly.
¤ Result: The diagnostic LCD does not
display "18". The alarm does not sound.
Replace the down limit switch.
15. Raise up the platform to the potholes
protection device spread.
⊙ Result: The diagnostic LCD display "18".
The alarm does not sound and the machine is
function properly
¤Result: The diagnostic LCD dose not
display "18". The alarm does not sound and
replace the down limit switch.
16. Press the platform up button and attempt
to raise the platform to approximately
2.5m.
17. Lift the safety arm, move it to the center of
the scissor arm and rotate down to a
vertical position.
18. Lower the platform onto the safety arm.
Crushing hazard.
Keep hands clear of the safety arm when
lowering the platform.
19. Turn the key switch to the off position.
20. Disconnect the platform controls from the
ECU cable.
21. Securely install the connector of the ECU
cable into the platform control cable.
22. Install the connector of the platform
controls.
23. Connect the two wires in the down limit
switch correctly and safely.
24. Install the cover of down limit switch.
25. Turn the key switch to platform control.
26. Raise the platform and return the safety
arm to the stowed position.
27. Lower the platform to the stowed position.
Level Sensor
28. Move the machine onto a grade which
exceed the rating of level sensor. Refer to
the serial label on the machine.
29. Press the platform up button and attempt
to raise the machine to 2m.
⊙ Result: The diagnostic LCD displays "LL".
The alarm sounds and the platform stops
lifting after the pothole guards are deployed.
The machine is function properly.
¤ Result: The diagnostic LCD does not
display "LL". The alarm sounds and the
platform continues to lift after the pothole
guards are deployed. Adjust or replace the
level sensor.
30. Press the drive function select button and
attempt to drive the machine on the slope.
⊙Result: The diagnostic LCD display "LL".
The alarm sounds. Steering and driving
function cannot operation. Machine is function
properly.
¤ Result: The diagnostic LCD does not
display "LL". The alarm does not sound and
the steer and drive functions operate. Adjust
or replace the level sensor.
31. Lower the platform to the stowed position,
move the machine onto a firm, level
surface.
Pothole Limit Switches
32. Place a wooden block approximately 5cm
tall under the right pothole guard.
33. Press the raise function button, attempt to
raise the machine 2m.
⊙ Result: The pothole guard contacts the
block and does not fully deploy. The
diagnostic LCD displays "18". The alarm
Bekijk gratis de handleiding van Ekko ES60E, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ekko |
| Model | ES60E |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8709 MB |
