Einhell GE-SC 35/1 Li handleiding
Handleiding
Je bekijkt pagina 23 van 155
GB
- 23 -
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Damage to hearing if no suitable ear protec-
tion is used.
2. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Warning!
This equipment generates an electromag-
netic fi eld during operation. Under certain
circumstances this fi eld may actively or pas-
sively impede medical implants. To reduce
the risk of serious or fatal injuries, we recom-
mend persons with medical implants to con-
sult their doctor and the manufacturer of the
medical implant prior to using the equipment.
5. Before starting the equipment
Important!
The equipment is supplied without batteries and
without a charger is allowed to be used only with
the lithium-ion batteries of the Power-X-Change
series!
Power-X-Change
•
18 V, 1.5 Ah, 5 lithium-ion cells
•
18 V, 3.0 Ah, 10 lithium-ion cells
•
18 V, 5.2 Ah, 10 lithium-ion cells
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Warning!
Always pull out the safety plug before performing
any adjusting, repair, maintenance or cleaning
work on the equipment.
The scarifi er is delivered unassembled. The com-
plete push bar and the rear wheels must mounted
before using the scarifi er.
Follow the operating instructions step-by-step
and use the pictures provided as a visual guide to
easily assemble the machine.
Fitting the rear wheels (see Fig. 3 and Fig. 4)
•
Insert the axles of the rear wheels into the
openings provided (Fig. 3 / Item A).
•
Secure the wheels with the screws provided .
(Fig. 4/ Item 19)
Fitting the push bar brackets (see Figs. 5
and 6)
•
Remove the quick-release lever (Fig. 5/
Item 13) and the washer (Fig. 5/Item 17)
•
Connect the push bar bracket (Fig. 5/Item 7)
to the fastening screw. Make sure that the
curve in the tube (Fig. 6/Item A) is on the out-
side.
•
Now put the washer back on and tighten with
the quick-release lever.
The same tilt angle must be set for both push bar
brackets!
Fitting the lower push bar (see Fig. 7)
•
Slide the lower push bar (Fig. 7/Item 6) onto
the push bar brackets.
•
Now join the tubes together using the screws
(Fig. 7/Item 18), washers (Fig. 7/Item 17) and
quick-release levers (Fig. 7/Item 13) supplied.
Fitting the upper push bar (see Fig. 8 to
Fig. 10)
•
The upper push bar (Fig. 8/Item 5) has two
holes one beneath the other for further height
adjustment of the push bar.
•
Position the upper push bar (Fig. 8 / Item 5)
such that its holes line up with the holes of the
lower bar.
•
Now join the tubes together using the screws
(Fig. 8/Item 18), washers (Fig. 8/Item 17) and
quick-release levers (Fig. 8/Item 13) supplied.
•
Use the cable clips (Fig. 9/Item 12) to attach
the power cable to the tubes of the push bars
so that it is possible to open and shut the
ejector flap (Fig. 10/Item 12).
Please ensure that the ejector fl ap can be opened
and closed easily!
Anl_GE_SC_35_1_Li_SPK9.indb 23Anl_GE_SC_35_1_Li_SPK9.indb 23 20.03.2019 06:16:4420.03.2019 06:16:44
Bekijk gratis de handleiding van Einhell GE-SC 35/1 Li, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Einhell |
| Model | GE-SC 35/1 Li |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 19809 MB |
