Dremel Multi-Max MM35 handleiding
Handleiding
Je bekijkt pagina 4 van 56
-4-
accessories. The accessories are very sharp.
Wear protective gloves when changing cutting
accessories. Accessories become hot after
prolonged usage.
Use thick cushioned gloves and limit the exposure
time by taking frequent rest periods. Vibration
caused by the tool may be harmful to the hands and
arms.
Before scraping, check workpiece for nails. If there
are nails, either remove them or set them well
below intended finished surface. Striking a nail with
accessory edge could cause the tool to jump.
Do not wet sand with this tool. Liquids entering the
motor housing is an electrical shock hazard.
Never work in area which is soaked with a liquid,
such as a solvent or water, or dampened such as
newly applied wallpaper. There is an electrical shock
hazard when working in such conditions with a power
tool and heating of the liquid caused by scraping
action may cause harmful vapors to be emitted from
workpiece.
Always wear eye protection and a dust mask for
dusty applications and when sanding overhead.
Sanding particles can be absorbed by your eyes and
inhaled easily and may cause health complications.
Use special precautions when sanding chemically
pressure treated lumber, paint that may be lead
based, or any other materials that may contain
carcinogens. A suitable breathing respirator and
protective clothing must be worn by all persons
entering the work area. Work area should be sealed by
plastic sheeting and persons not protected should be
kept out until work area is thoroughly cleaned.
Do not use sandpaper intended for larger sanding
pads. Larger sandpaper will extend beyond the sanding
pad causing snagging, tearing of the paper or kick-back.
Extra paper extending beyond the sanding pad can also
cause serious lacerations.
Additional Safety Warnings
Always inspect blade for damage (breakage, cracks)
before each use. Never use if damage is suspected.
GFCI and personal protection devices like electrician’s
rubber gloves and footwear will further enhance your
personal safety.
Do not use AC only rated tools with a DC power
supply. While the tool may appear to work, the
electrical components of the AC rated tool are likely to
fail and create a hazard to the operator.
Keep handles dry, clean and free from oil and
grease. Slippery hands cannot safely control the power
tool.
Develop a periodic maintenance schedule for
your tool. When cleaning a tool be careful not to
disassemble any portion of the tool since internal
wires may be misplaced or pinched or safety guard
return springs may be improperly mounted. Certain
cleaning agents such as gasoline, carbon tetrachloride,
ammonia, etc. may damage plastic parts.
Risk of injury to user. The power cord must only be
serviced by a Dremel Service Facility.
Some dust created by power
sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other
masonry products, and
• Arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
editing_1600A014GW MM35 201808.indd 4editing_1600A014GW MM35 201808.indd 4 7/28/2023 9:58:18 AM7/28/2023 9:58:18 AM
Bekijk gratis de handleiding van Dremel Multi-Max MM35, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Dremel |
| Model | Multi-Max MM35 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6867 MB |
