Digi-Pas DWL5800XY handleiding
Handleiding
Je bekijkt pagina 45 van 73
Digi-Pas
®
© 2023 Digipas Technologies Inc. All Rights Reserved.
www.digipas.com
Page 39
DWL-5x000XY DATA SHEET
Byte [n] Command Descriptions
Byte [0] 0x61 To Computer / From Sensor
Byte [1] 0x13 Single Axis Position / Vibro Mode
Byte [2] 0x00
Vibro Value
Byte [3] 0x03
Byte [4] 0xD0
Byte [5] 0x90
Byte [6] 0xCC
Fixed Dummy
Byte [7] 0xCC
Byte [8] 0xCC
Byte [9] 0xCC
Byte [10] 0xAA CRC16 High
Byte [11] 0x3A CRC16 Low
Following equation shows the conversion of angle from the received data:
For DWL5800XY
Vibrometer g = (((Byte [5] << 24) + (Byte [4] << 16) + (Byte [3] << 8) + Byte [2]) - 250000) /
100000
For DWL5500XY
Vibrometer g = (((Byte [5] << 24) + (Byte [4] << 16) + (Byte [3] << 8) + Byte [2]) - 250000) / 100000
For DWL5000XY
Vibrometer g = (((Byte [5] << 24) + (Byte [4] << 16) + (Byte [3] << 8) + Byte [2]) - 25000) / 10000
6.5.4. Calibration Mode
To set the tilt sensor module into Calibration Mode:
<< (To sensor) : 0x06, 0x01, 0x0B, 0xA0, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
<< (To sensor) : 0x06, 0x01, 0x0B, 0xB0, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
Byte [n] Command Descriptions
Byte [0] 0x06 From Computer
Byte [1] 0x01 To Sensor
Byte [2] 0x0B Calibration Mode
Byte [3] 0xA0 0xA0 : Acknowledgement
0xB0 : Start current calibration step
Byte [4]~[11] 0x00 Not Applicable
Data received from tilt sensor module:
>> (From sensor) : 0x61, 0x1B, 0x00, 0x00, 0x13, 0x01, 0x88, 0xDD, 0xDD, 0xDD, 0xAA, 0x3A
Byte [n] Command Descriptions
Byte [0] 0x61 To Computer / From Sensor
Byte [1] 0x1B Single Axis Position / Calibration Mode
Byte [2] 0x00 Calibration Feedback
0x17 : Idle /Current calibration step nished
0x0A : Counting
Byte [3] 0x00 Calibration Count
0x01 - 0x1E : Counting Up
Byte [4] 0x13 Not Applicable
Byte [5] 0x01 Calibration Step
0x01: Calibration Step 1 ready
0x02: Calibration Step 2 ready
0x03: Calibration Step 3 ready
0x04: Calibration Step 4 ready
0x05: Calibration Step 5 ready
0x06: Calibration Step 6 ready
0x07: Calibration Step 7 ready
0x08: Calibration Step 8 ready
Byte [6] 0x88 Not Applicable
Byte [7]~[9] 0xDD Fixed Dummy
Byte [10] 0xAA CRC16 High
Byte [11] 0x3A CRC16 Low
It is advised to perform calibration of the tilt sensor module in a controlled temperature set-
ting.
* Please refer to 6.5.4.1 for detailed calibration steps
6.5.4.1. Detailed Calibration Steps :
1. Please refer to Appendix 1 for proper instrument setup for calibration. Send the follow-
ing command from computer to respective sensor to make sure the sensor is ready for
calibration mode:
<< (To sensor): 0x06, 0x01, 0x0B, 0xA0, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
Byte [n] Command Descriptions
Byte [0] 0x06 From Computer
Byte [1] 0x01 To Sensor
Byte [2] 0x0B Calibration Mode
Byte [3] 0xA0 Acknowledgement to sensor module
Byte [4]~[11] 0x00 Not Applicable
Bekijk gratis de handleiding van Digi-Pas DWL5800XY, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Digi-Pas |
| Model | DWL5800XY |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10950 MB |
