DeWalt DXV20SPTA handleiding
Handleiding
Je bekijkt pagina 21 van 100
SHUT DOWN/TRANSPORTATION (Fig. A)
1. Turn on/off switch to the OFF position.
2. Unplug the unit.
3. Store the power cord wrapping it around the
sturdy handle/cord wrap as shown.
4. When transporting in vehicles, secure the machine.
MAINTENANCE
The DEWALT appliance has been designed to operate
overa long period of time with a minimum of
maintenance.Continuous satisfactory operation
depends upon proper appliance care and regular
cleaning.
WARNING: To reduce the risk of injury,
turn appliance off and disconnect
appliance from power source before
installing and removing accessories,
before adjusting or changing set-ups or
when making repairs. An accidental start-up
can cause injury.
WARNING: For user servicing, the machine must
be dismantled, cleaned and serviced, as far as is
reasonably practicable, without causing risk to the
maintenance staff and others. Suitable precautions
include, decontamination before dismantling, provision
is dismantled, cleaning of the maintenance area and
suitable personal protection.
• The manufacturer, or an instructed person, shall
perform a technical inspection at least annually,
damage, air tightness of the machine and proper
function of the control mechanism.
• When carrying out service or repair operations, all
contaminated items which cannot be satisfactorily
cleaned, are to be disposed of; such items shall be
disposed of in impervious bags in accordance with
any current regulation for the disposal of such waste.
• For dust extractors it is necessary to provide for an
adequate air change rate L in the room if the exhaust
air is returned to the room.
NOTE: Refer to national regulations is necessary.
19
English
3
2
1
6
TO EMPTY DUST TANK (Fig. K)
WARNING: To reduce the risk of injury from
accidental starting, unplug power cord before emptying
the dust tank .
1. Remove the power head assembly of the wet/dry
vac bypulling outward on the lid clips located on each
side of the vac. Lift off the power head assembly.
2. Dump the tank dust tank into the proper waste
disposal container.
To Install Foam Filter
This cleaner requires minimal conversion when going
be used for vacuuming small amounts of liquid. For
best results when vacuuming large amounts of liquid,
as
shown in Fig. J
to protect the motor and minimize the potential for
misting that may appear in the exhaust air or dripping
of liquid around the lid.
17
FILTER (Fig. A, H, I)
FILTER CARE
MUST be installed correctly and in good condition.
WARNING: Appropriate personal protective
equipment like dust mask and gloves should be used
NOTE:
2. Release lid latches and remove vacuum
head . from canister. Place vacuum head on a
level surface upside down.
on the plastic end cover as shown, and carefully
remove from head, ensuring debris does not fall into
mounting hole.
NOTE:
4. If the bottom side of the vacuum head needs to
be cleaned, use a cloth dampened with water and
mild soap and allow it to dry. Dispose the cloth in an
appropriate container.
NOTE: If there is any doubt on the condition of the
WARNING: Never use compressed air or a brush
If needed, gently tap against a hard surface or rinse with
room temperature water and let air dry. Cleaning of the
maintain maximum performance and continue to function.
depending on use and care.
To Install Clean Connect™ Filter
NOTE:
3. Place the vacuum head onto the dust tank and
secure it by closing the lid latches .
5
4
9
4
15
16
4
5
To Remove Clean Connect™ Filter
1. Turn on/off to the OFF position ( O )
and unplug cord from outlet.
3
Bekijk gratis de handleiding van DeWalt DXV20SPTA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | DeWalt |
| Model | DXV20SPTA |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 19750 MB |
