DeWalt DXF1616 handleiding
Handleiding
Je bekijkt pagina 6 van 23
4
Keep electrical cords in good
condition. Do not use worn, bare, or frayed
cords because they can cause electric shock.
Operating equipment at low
voltage can cause it to overheat. Using an
excessively long extension cord can cause the
cord to overheat.
USE OF EXTENSION CORDS
WITH FAN
Minimum Gauge for Extension Cord Sets
Volts
Total Length of Cord in Feet (meters)
120V
240V
AWG
Not More
Than
More
Than
Ampere Rating
25(7.6)
50(15.2)
0
6
10
6
18
18
16
16
16
16
16
14
14
14
12
12
10
12
50(15.2)
100(30.5)
100(30.5)
200(61.0)
150(45.7)
300(91.4)
Only use a grounded extension cord that is rated
at least 15 amps and has a third-wire ground.
When a long extension cord is used to connect
the fan, a voltage drop occurs. The longer the
cord, the greater the voltage drop. This results
in less voltage being supplied to the fan and
increases the amount of current (amp) draw or
reduces performance. A heavier cord with a
larger wire size will reduce the voltage drop. Be
sure to choose a cord that will supply enough
volt
age to operate the fan. The table below
indicates appropriate gauge for extension
cords.
ENGLISH
The fan is for use on a nominal 120V circuit, and
should be connected to a grounding outlet that
looks like that illustrated in sketch a. A temporary
adaptor, which looks like the adaptor illustrated in
sketch b, may be used to connect this plug to a
2-pole receptacle as shown in sketch b if a
properly grounded outlet is not available. The
temporary adaptor should be used only until a
properly grounded outlet can be installed by a
quali
lug, and the like, extending from the adaptor
must be connected to a permanent ground such
as a properly grounded outlet box cover.
Whenever the adaptor is used, it must be held
in place by the metal screw.
NOTE:
IN CANADA, THE USE OF A
TEMPORARY ADAPTOR IS NOT PERMITTED
BY THE CANADIAN ELECTRICAL CODE.
Ensure that the fan is connected to an outlet
a b
ADAPTER
GROUNDING PIN
GROUNDED
OUTLET
BOX
FAN OPERATION
Before assembling the fan, make sure all parts
are present. Compare parts with contents list.
If any part is missing or damaged, do not
attempt to assemble, install, or operate the
product. Contact customer service for
replacement parts. Unplug fan before
assembling any parts to it.
1.
2. Fan Cradle Assembly:
Simple assembly is required to use this fan.
Tools Required (Not Included):
#2 Phillips Screwdriver or Suitable Drill
Equipped with #2 Phillips Bit.
ARNING: W
ARNING: W
ARNING: W
3. Fan Operation: Always operate the fan
with the cradle in its upright position. The fan
itself can be tilted into various positions
depending on applications, including straight
upward.
• Align and insert the to the side hole on
and , tighten them with the . Do not over
-tighten. Repeat above process for the
opposite side of fan.
1
Adjustment knob
2
Foot support
4
Drum
3
Adjustment knob pad
6
Screw
5
Cradle base
21
3 4
• Press the into the back hole on , then
tighten the on each side of the .
25
26
1
2
3
4
5
7
1
2
3
4
5
6
Bekijk gratis de handleiding van DeWalt DXF1616, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | DeWalt |
| Model | DXF1616 |
| Categorie | Ventilator |
| Taal | Nederlands |
| Grootte | 4081 MB |
