DeWalt DW679K handleiding
Handleiding
Je bekijkt pagina 19 van 72
ENGLISH
15 en - 4
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Adjusting the depth of cut (fig. B)
• Turn the planing depth adjustment knob (4) to
the required depth of cut.
One graduation corresponds to a depth of cut of
0.1 mm.
Attaching and removing the parallel fence
(fig. A & C)
The parallel fence (12) is used for optimum tool
control on narrow workpieces.
• Slacken the wing bolt (6).
• Fit the parallel fence (12) in the hole (7) from
either side.
• Tighten the wing bolt.
• To remove the parallel fence, proceed in
reverse order.
Removing reversible cutters (fig. D)
• Loosen the three bolts (13) with the spanner (14)
supplied.
• Flap the side guard (8) up.
• Slide the cutter (15) out of its holder.
• Reverse the cutter or replace it.
Always replace both cutters.
• Slide the cutter into the holder. Make sure that
the cutter is flush with the planing shoe (16).
• Tighten the three bolts (13).
Instructions for use
Always observe the safety instructions
and applicable regulations.
Prior to operation:
• Adjust the depth of cut.
• If necessary, fit and adjust the parallel fence.
Use sharp cutters only.
Switching on and off (fig. A)
Your planer is equipped with a safety switch to
prevent inadvertent operation.
• Switching on: press the lock-off button (2) and
subsequently press the on/off-switch (1).
• Release the lock-off button (2).
• Switching off: release the on/off-switch (1).
Always switch off the tool when work is finished
and before unplugging.
Planing (fig. A)
• Switch the tool on as described.
• Slowly move the planer over the workpiece.
• The feed speed should not be too high,
especially when using the maximum
depth of cut and planing width.
• Remember that several shallow cuts are
better than one deep cut.
• Switch the tool off.
Your planer is equipped with a parking shoe (11).
After switching off the tool can be put down without
waiting for the cutters to come to a standstill.
Bekijk gratis de handleiding van DeWalt DW679K, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | DeWalt |
| Model | DW679K |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7887 MB |
